• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
[WTB] Two OEM Intake Manifold Bolts
#1
Hello all,

I am looking for one standard length oem intake manifold bolt and one longer one that fits on the choke stove. I am looking for the bolts to have the same markings as the one in the pictures.

Thank you!


[Image: IMG_6329.jpg]

[Image: IMG_6330.jpg]

[Image: IMG_6331.jpg]

[Image: IMG_6332.jpg]
  Reply
#2
(12-10-2017, 04:24 PM)4mm Wrote: Hello all,

I am looking for one standard length oem intake manifold bolt and one longer one that fits on the choke stove. I am looking for the bolts to have the same markings as the one in the pictures.

Thank you!

Give me the length of the bolts you need and I'll check what I have (or let me know what year and engine you have.)

Thanks from MotorCity Mustang!
http://stores.ebay.com/MotorCity-Mustang
  Reply
#3
I don't throw anything away. I probably have those too. I'll go wander out into the garage.

'Mike'
73 Convertible - 351C/4V CC heads/4bolt/forged flat tops/comp 270/rhodes/mallory unilite/tri-power/hookers/glasspacks/c6/3.50 limited slip/Gear Vendors/Global West sub frames, strut rods and shelby style traction bars/ Rear sway bar/tilt steering (not original)

Pics of modifications included in:
  Reply
#4
It’s been a while and I thank you for the replies. The bolts are 3/8-16 and one is 2.25” in length and the other is 2.75 in length.

The most important item to me is that the head markings are the same. The intake manifold is the last item I need to address for this 351C 4V engine.

Thank you!
  Reply
#5
(12-23-2017, 10:33 AM)4mm Wrote: It’s been a while and I thank you for the replies. The bolts are 3/8-16 and one is 2.25” in length and the other is 2.75 in length.

The most important item to me is that the head markings are the same. The intake manifold is the last item I need to address for this 351C 4V engine.

Thank you!

I will head down to the garage when I get back from Chicago for Christmas and find those bolts for you.

Thanks from MotorCity Mustang!
http://stores.ebay.com/MotorCity-Mustang
  Reply
#6
Hey, I forgot about this post. I will go wander out into the garage in a bit and take a look.

'Mike'
73 Convertible - 351C/4V CC heads/4bolt/forged flat tops/comp 270/rhodes/mallory unilite/tri-power/hookers/glasspacks/c6/3.50 limited slip/Gear Vendors/Global West sub frames, strut rods and shelby style traction bars/ Rear sway bar/tilt steering (not original)

Pics of modifications included in:
  Reply
#7
I have some of the shorter ones, with the 'F'. It's hard to see in your pictures but mine have the three lines coming from the 'F' like I see in your 'N' pictures. There are also what appears to be three characters on the 'washer' side of the bolt. Looks like 'R', 'S' and 'U'. These would have been on a 73 Mustang with a Cleveland.

They are in good shape, need to be cleaned up. If you want them PM me your address and I will ship you the nicest two.

I'll keep looking for the others but I don't think I will have much luck. If I remember correctly the choke stove for the Cleveland were smaller than the other bolts? What engine are you working on?

'Mike'
73 Convertible - 351C/4V CC heads/4bolt/forged flat tops/comp 270/rhodes/mallory unilite/tri-power/hookers/glasspacks/c6/3.50 limited slip/Gear Vendors/Global West sub frames, strut rods and shelby style traction bars/ Rear sway bar/tilt steering (not original)

Pics of modifications included in:
  Reply
#8
I found what I believe to be the choke stove bolt from my cleveland. However, it is a smaller thread and has an 'F' stamped on the head.
I look at your picture and the two bolts shown in the picture don't appear to have the same thread.

'Mike'
73 Convertible - 351C/4V CC heads/4bolt/forged flat tops/comp 270/rhodes/mallory unilite/tri-power/hookers/glasspacks/c6/3.50 limited slip/Gear Vendors/Global West sub frames, strut rods and shelby style traction bars/ Rear sway bar/tilt steering (not original)

Pics of modifications included in:
  Reply
#9
(12-25-2017, 10:18 AM)will e Wrote: I have some of the shorter ones, with the 'F'. It's hard to see in your pictures but mine have the three lines coming from the 'F' like I see in your 'N' pictures. There are also what appears to be three characters on the 'washer' side of the bolt. Looks like 'R', 'S' and 'U'. These would have been on a 73 Mustang with a Cleveland.

They are in good shape, need to be cleaned up. If you want them PM me your address and I will ship you the nicest two.

I'll keep looking for the others but I don't think I will have much luck. If I remember correctly the choke stove for the Cleveland were smaller than the other bolts? What engine are you working on?

I apologize for not replying sooner, I just saw the post.

Working on a 351C 4v and yes the choke stove bolts are a smaller diameter but longer.

I’ll take them! Sending a PM.


Sent from my iPhone using Tapatalk
  Reply
Share Thread:  


Possibly Related Threads…
Thread Author Replies Views Last Post
  [WTB] 1971 EXHAUST MANIFOLD HEAT SHIELD for 351c TexasBoss 5 247 11-29-2019, 05:23 PM
Last Post: TexasBoss
  Aluminum Intake Manifold piper62j 2 317 07-12-2019, 07:47 AM
Last Post: mjseakan
  WTB 351C 2V PASSENGER EXHAUST MANIFOLD Cudben 6 670 06-24-2019, 07:42 AM
Last Post: OMS
runninpony [WTB] exhaust manifold rmcclellan 1 198 06-23-2019, 03:46 PM
Last Post: DeereFanatic
  WTB Passenger side Exhaust manifold for 72 Mach 1 - DOAE-9430-B baz70 7 489 03-10-2019, 05:28 PM
Last Post: baz70



Users browsing this thread: 1 Guest(s)