• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
[WTB] Throttle cable holder
#1
Hello, I was wondering if anyone has a throttle cable holder, that the mounting holes are 180 degrees (or inline) to the throttle cable? The one on the car is 90 degrees.

Thanks
Robert

[Image: 0722121231b.jpg]
  Reply
#2
I would get a hold of Don at ohio mustang supply or Motorcity mustang. They should have what you need.

My garage http://www.7173mustangs.com/forum-garage...rxt_uid=40

73 mach 1 351c 4v cc ported, torker2, 750 edelbrock,C6.
73 fastback 351c 2v,performer intake,600 edelbrock,fmx, 325 trac-lok.
  Reply
#3
Just curious, is that a stock or aftermarket manifold? A few more engine shots would be nice...unless you posted previously and I missed it.

I have inquired of Don of OMS for such an item within the past couple of weeks and he came up empty...but that doesn't mean he hasn't found something in the meantime.

For an aftermarket/Edelbrock Performer manifold and carb in a 351W, I had to make my own. I had to use thick aluminum, sheared at a friends sheet metal shop, and then bend it with my vice and drill my own holes. But it has held up pretty well and doesn't look too funky.

If you don't find one, give me an address and I will hunt done the spare flat pieces I have made and mail one to you.

If you do find one, see if your source has 2 as I need one for my 351C stock OTC manifold application.

james

[Image: 11jmcuc.png]
351C Bold Manners, Brash Attitude
Favorite Teams: Michigan Wolverines and Whoever Is Playing Ohio State.

When I drive past a herd of cows, the cows MOO at me
  Reply
#4
Wolverine;81557 Wrote:Just curious, is that a stock or aftermarket manifold? A few more engine shots would be nice...unless you posted previously and I missed it.

I have inquired of Don of OMS for such an item within the past couple of weeks and he came up empty...but that doesn't mean he hasn't found something in the meantime.

For an aftermarket/Edelbrock Performer manifold and carb in a 351W, I had to make my own. I had to use thick aluminum, sheared at a friends sheet metal shop, and then bend it with my vice and drill my own holes. But it has held up pretty well and doesn't look too funky.

If you don't find one, give me an address and I will hunt done the spare flat pieces I have made and mail one to you.

If you do find one, see if your source has 2 as I need one for my 351C stock OTC manifold application.

james

Thanks James, it's an Edelbrock intake, I'm pretty sure I could fab someting up, but I'd like to keep it as stock as possible. I post up, should I find something, we have a Mustang junk yard here in Richmond VA, might find something there.

Robert
  Reply
Share Thread:  


Possibly Related Threads...
Thread Author Replies Views Last Post
  speedometer cable 1972 Vicus 10 1,039 10-30-2016, 12:19 PM
Last Post: Motorcity Mustang
  WTB: Fresh Air Vent cable ScooterDog 7 690 06-05-2016, 05:13 PM
Last Post: Motorcity Mustang
  center gauge benzel and instrament holder will e 3 773 03-06-2015, 08:16 PM
Last Post: mrmach1
  Anyone have an accelerator cable firewall grommet jeff8877 1 415 06-24-2014, 11:57 AM
Last Post: OMS
  1973 Coupe Emergency Brake Cable kat29rn@aol.com 2 532 06-12-2013, 05:24 PM
Last Post: kat29rn@aol.com
  Throttle cable bracket 73 351c 2v Mikes73 1 863 11-12-2012, 07:47 PM
Last Post: Motorcity Mustang
  Accelerator cable marks73 3 594 09-15-2012, 06:38 PM
Last Post: Jeff73Mach1
  Need a throttle cable plate! 71_resurrection 4 847 09-14-2012, 07:13 PM
Last Post: 71_resurrection



Users browsing this thread: 1 Guest(s)