• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
What does it take to stroke a 351c
#1
Yes I am pretty sure I have decided to use the stock 351c instead of the 460... Big Grin   I reserve the right to change my mind again though... Haha 

So, I have some questions on stroking the 351.  I know several of you have done this.

You have to clearence the block??  
Can you do your own clearancing or does the machine shop have to do it?  
What do you do for clearencing, stick the crank in and then see where the block needs to be ground down?  
Just use a die grinder to grind the block down?
What rotating assembly do you recommend?  Link to it??

Thanks!
Wade
1972 Mach 1 351 cj 4speed
"We confide in our strength, without boasting of it; we respect that of others, without fearing it."--Thomas Jefferson

  Reply
#2
(09-29-2018, 10:40 AM)scgamecock Wrote: Yes I am pretty sure I have decided to use the stock 351c instead of the 460... Big Grin   I reserve the right to change my mind again though... Haha 

So, I have some questions on stroking the 351.  I know several of you have done this.

You have to clearence the block??  
Can you do your own clearancing or does the machine shop have to do it?  
What do you do for clearencing, stick the crank in and then see where the block needs to be ground down?  
Just use a die grinder to grind the block down?
What rotating assembly do you recommend?  Link to it??

scgamecock,
Throw everything away and keep the block and possibly the cylinder heads.
And oh yes, one should have lots of cash on hand.
That's about it,
Boilermaster
  Reply
#3
You can go to a 4-inch stroke, which will give you 408 cubic inches with a 0.030 over bore (4.030"), without any problems.

There are a few manufacturers that have kits, Howard's Cams, SCAT, Manley, and Eagle sells their's on Summit Racing
https://www.summitracing.com/search/depa...4294880931



“If you can't explain it simply, you don't understand it well enough.”
--Albert Einstein
  Reply
#4
I ran a scat 408 kit and did not need to clearance the block at all.

Kevin

1971 Mach 1
408C Stroker
C4 w/3,000 stall
8.8" Rear w/3.73's
Disc brakes all way around.

[Image: 28ivsix.png]




                                                                                             
[+] 1 user Likes turtle5353's post
  Reply
#5
A good machine shop!

run_horse Run Horse Run!
John 72 Q Code
  Reply
#6
I ran with the Scat 9000 series 4.00 inch stroke cast crank and no clearance problems except with the oil pan but the Kevko solved this.
Only other issue you might have is when using the Scat forged crank is to make sure you use a spacer for the harmonic balancer
Just use "stroker clearanced" rods and shouldn't be any problems but as always check then check again
Would also recommend machining the block for the 351W one piece rear main seal
If you go for the 3.85 inch stroke (393) you will have less clearance issues, good luck
  Reply
#7
Call Tim Meyer

https://www.tmeyerinc.com/


  Reply
Share Thread:  


Possibly Related Threads...
Thread Author Replies Views Last Post
  351C Fuel Delivery Problem Rumblefish 11 200 Yesterday, 05:59 AM
Last Post: Fabrice
  What externally will work on a 460 from a 351c scgamecock 15 379 09-29-2018, 01:57 PM
Last Post: 7173Vert
  difference in 351C-2v heads Vinnie 27 838 09-23-2018, 06:49 AM
Last Post: Vinnie
  Increasing Power 73 351c Cobra Jet bytor2112 4 326 09-05-2018, 05:33 PM
Last Post: Carolina_Mountain_Mustangs
  351C fuel pumps? Hemikiller 5 407 09-02-2018, 07:12 AM
Last Post: clevelandcoupe
  1973 351C vacuum lines and eventual other questions scottyrocks 14 589 08-12-2018, 11:53 AM
Last Post: Don C
  Correct 351C Power Steering Hoses? street rod mach 1 7 335 08-12-2018, 08:26 AM
Last Post: NOT A T5
  351c cam lobe ID. Have to measure lift Ryunker 8 487 07-23-2018, 06:04 PM
Last Post: Ryunker



Users browsing this thread: 1 Guest(s)