• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Water pump replacement
I have a 1972 ford mustang 351c I replaced the water pump only used one gasket did I need to use both of them I got it running today and water is coming out of the left side of the motor by the oil stick did I do something wrong.
May be silly question, but did you assemble with just the gasket and no sealant?
Were the bolts/threads clean so you could set them back with proper torque?

73 modified Grandé 351C. Almost done. 
71 429CJ. In progress
I never replaced a water pump but it sounds like you re-used one of the old gaskets? I hope I'm wrong coz you should never re-use a gasket.
if the 351 is similar to the 302 as far as the pump... the bolts on the left (pass) go into the water jacket. u need some kind of sealant on them. if it really is leaking from gasket u gotta pull it and see whats going on. on side note when getting gasket kits a lot of them come with duel gaskets... some fit and the other will not. this is true if u get a rebuild gasket kit...
If you have a leak there is something wrong for sure. Are you sure hoses are in place and tight also?
When you had the pump off you should clean all the bolts really good and I apply some anti seize and bit of RTV to the threads of the ones that go into water jacket. Cannot say by memory which ones do.
You should apply a small amount of RTV or sealer to both sides of the gasket. It is also easy to knock the gasket out of position when installing. It is a great help to take a couple of long bolts and cut the heads off and put one on each side to slide the gasket over and get in place then slide the pump on and get the bolts started and then remove your guide bolts. You can also use threaded rod cut to length.
You also need the special thermostat for a 351 C or you will have heat issues. Correct one is shown in the picture. Has a hat like extension that goes into the baffle down inside the block. Use anti seize on the thermostat housing bolts also.
Only one gasket should be needed.
[Image: 100_3324.jpg]

[Image: 100_3325.jpg]

When a man is in the woods and talks and no women are there is he still wrong??
Did you clean the timing cover before installing the water pump? It has to be clean and smooth.

You have to select the gasket that matches the water pump.

You need to put gasket sealer on both sides of the gasket. You need to use oil resistant thread sealer on all of the bolts.

“If you can't explain it simply, you don't understand it well enough.”
--Albert Einstein
and the timing covers get pitted over the years and if they aren't in good shape, a seal can be hard to get without a good sealant added to the gasket surface.

Probably have to pull it and try again, but the second time will be easier.

[Image: 1_01_07_15_8_53_18.png]

"I love my Hookers!" and "Get some Strange" probably have a different connotation to non automotive enthusiasts!
Thank you all I did new gasket on with pump. Maybe try sealing the bolts first before I pull the water pump.
I know we used a gasket between the timing cover and the block AND a gasket between the timing cover and the water pump.

Also, in case you need it, here's a guide for the bolts...

[Image: water_pump_bolt_orientation.png]

Don't be afraid to try something new. Remember, amateurs built the Ark...Professionals built the Titanic! thumb

[+] 1 user Likes EBSTANG's post
Share Thread:  

Possibly Related Threads…
Thread Author Replies Views Last Post
  Direction's flector replacement Jean-Pierre 9 899 12-13-2019, 11:32 PM
Last Post: B229218
  Water pump gasket sealant RC92234 6 307 11-30-2019, 06:52 PM
Last Post: RC92234
  Wiper blade replacement Mikey 8 445 11-05-2019, 08:39 PM
Last Post: goodnigh
Wrench Rag Joint Replacement Jon71 12 504 10-08-2019, 07:54 PM
Last Post: Jon71
  351 Cleveland fuel pump probs. Fordboy71 5 386 09-29-2019, 08:37 AM
Last Post: Carolina_Mountain_Mustangs

Users browsing this thread: 1 Guest(s)