• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Viper Switch wiring
#1
Hi

I changed the wiring to an EZ wiring harness. Now its time to connect the viper, but Im not sure which wire goes were.

4 wires going out to the viper motor, Im guessing one is low, High, return to startposition and Power ?

1 one wire is going out to the washer motor

2 wires in from Power ACC, and something else.

Im only have one wire in to the switch from the EZ wiring harness.

But how should it be connected. I have the workshop manual but I cannot figure it out. The switch is brand new. Help is much appreciated

Regards Rob

   
   

For knowing your limit you have to pass it thumb
  Reply
#2
Go to the Data tab at the top of this page and download the wiring diagram for your car. Use the wire color codes to determine on how to connect the new harness. There are separate sheets just for the wiper switch wiring.



“If you can't explain it simply, you don't understand it well enough.”
--Albert Einstein
  Reply
#3
Hi

I have the schematics but the colors on the motor doesnt seems to ad up right. Il have a closer look at it tomorrow

Regards Rob

For knowing your limit you have to pass it thumb
  Reply
#4
Download the schematic for the '71, it shows the layout of the switch.



“If you can't explain it simply, you don't understand it well enough.”
--Albert Einstein
  Reply
#5
Okay Thanks :-)

For knowing your limit you have to pass it thumb
  Reply
#6
So

I hooked Everything as the wiring diagram shows. The vipers work in slow and high speed, but they do not go back to park position. So I measured the park wire and there is no Power comming from it. I switched between main in and park wire , and the vipers go to park. But when in park the battery charger I use for Power starts to make strange click noise. I Always use a 3 amp battery charger for testing stuff Before I hook up the battery. The switch is new out of the box. I didnt ground the switch but It should work anyway. Any clues ?

Regards Rob

For knowing your limit you have to pass it thumb
  Reply
#7
I opened up the motor, and cleaned Everything. Put it back together and now it works :-)

For knowing your limit you have to pass it thumb
  Reply
#8
Good job! thumb

Waiting for spring and summer...
  Reply
#9
thomas1984;283276 Wrote:Good job! thumb

Thanks :-)

For knowing your limit you have to pass it thumb
  Reply
Share Thread:  


Possibly Related Threads...
Thread Author Replies Views Last Post
  Tach and dash wiring/lights project rjpohl 4 217 01-04-2019, 05:18 PM
Last Post: rjpohl
  Alternator wiring problems rjpohl 7 180 12-28-2018, 02:43 PM
Last Post: Don C
  73 mustang ac wiring question DeereFanatic 1 176 12-21-2018, 08:03 PM
Last Post: midlife
  power antenna wiring rjpohl 1 157 11-21-2018, 07:37 PM
Last Post: Don C
  Need info on this wiring ... EvilPuppetMaster 0 183 10-08-2018, 04:05 PM
Last Post: EvilPuppetMaster
  Turn Signal Switch Advice Needed Rumblefish 11 433 09-23-2018, 03:34 PM
Last Post: Mister 4x4
  Under dash wiring harness routing 73429mach 5 506 09-03-2018, 07:14 PM
Last Post: 73429mach
  One wire alternator wiring Electric Power steering pump Robsweden 6 451 08-16-2018, 01:17 AM
Last Post: Robsweden



Users browsing this thread: 1 Guest(s)