• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Underhood light install picture
#1
Looking for a picture of the underhood light instalation. I have the option on my car, but do not recall the hole in the underside passanger side of the hood where it installed. I do not have any pictures from teardown of that.

BKDunha
72 Mach 1 H-Code (Concourse driven restoration)
67 S-Code Factory GT with 4-Spd

68 Mercury Cyclone (Pro-Street project)
  Reply
#2
Hi Brian,

Some examples I have been collecting for when the time comes for mine.

[Image: 2znxpg5.jpg]

[Image: 14b447q.jpg]

[Image: 2d0azow.jpg]

Jeff
1972 Q Code Convertible
  Reply
#3
That yellow picture above...

Big Grin
  Reply
#4
Thanx. Big help. Now to get that installed.

BKDunha
72 Mach 1 H-Code (Concourse driven restoration)
67 S-Code Factory GT with 4-Spd

68 Mercury Cyclone (Pro-Street project)
  Reply
#5
Great response guys! Brian, I was going to get a few pics of the convertible (under hood) but I see you already have some good (correct) placement pics. Only thing that might be little diffeent on mine could be the wiring loom. I will still try and get some pics later.

Ray

1971 Boss 351  
1972 Q code 4 speed convertible 
1971 Mustang Sportsroof  351-2V FMX 
1973 Mach 1 (parts car)
  Reply
#6
In review of my judging sheet from St. Augustine it was noted about tape on my underhood light harness. I had used original reproduction plastic (electrical) tape to sheath the harness from the bottom hood clip to the top hood clip. The original harness has a plastic strip that the hood clips are stapled to that runs the length of the harness from the bottom clip to the top. It would make sense to me that the tape was utilized to hold that strip in place. No point were deducted but it was noted. Does anyone have a known original underhood light assembly with the original covering on it. I have the fabric/asphalt sheathing I am just trying to understand if it was originally taped or not. Pictures help a lot and the ones above are not close enough to distinguish for my old eyes.

BKDunha
72 Mach 1 H-Code (Concourse driven restoration)
67 S-Code Factory GT with 4-Spd

68 Mercury Cyclone (Pro-Street project)
  Reply
#7
I have an original untouched one under my hood, it even has the part number sticker on it.

I'll take a few pictures when I get home tonight

[Image: 2zem9nk.jpg]
Iyman
1972 Mustang convertible run_horse  
Visit the Mustang Car Club of New England Facebook Page

Visit the Mustang Car Club of New England Web Page

  Reply
#8
bkdunha;273321 Wrote:In review of my judging sheet from St. Augustine it was noted about tape on my underhood light harness. I had used original reproduction plastic (electrical) tape to sheath the harness from the bottom hood clip to the top hood clip. The original harness has a plastic strip that the hood clips are stapled to that runs the length of the harness from the bottom clip to the top. It would make sense to me that the tape was utilized to hold that strip in place. No point were deducted but it was noted. Does anyone have a known original underhood light assembly with the original covering on it. I have the fabric/asphalt sheathing I am just trying to understand if it was originally taped or not. Pictures help a lot and the ones above are not close enough to distinguish for my old eyes.

I found this in my extra stuff... Hard to tell if the tape is original... Sheathing on each end still in place. Based on how the engine compartment main wiring harness is put together, this setup appears similar. We need Midlife to chime in on this to see what he has come across...

Btw, if someone needs this original piece for their car, just pm me proof that it came on your originally (ie marti or factory invoice showing you have the Convenience Group option), pay the shipping (should not be much, very light) and it's yours. It needs some restoring but you see what you are getting... My current restoration gets "ill" near cars that are optioned out... Cheers


Attached Files Thumbnail(s)
   
  Reply
#9
I think you need to clean out some pms. Your mailbox is full. Trying to send you the Marti. Jeff

Sent from my SM-G900V using Tapatalk
  Reply
#10
Twins;273342 Wrote:I think you need to clean out some pms. Your mailbox is full. Trying to send you the Marti. Jeff

Sent from my SM-G900V using Tapatalk

Done..., my apologies.
  Reply
Share Thread:  


Possibly Related Threads...
Thread Author Replies Views Last Post
  dome light stays on all the time rjpohl 14 435 11-30-2018, 06:30 PM
Last Post: Don C
  Dome Light Replacement EdM 5 227 11-08-2018, 11:13 PM
Last Post: 73pony
  dome light Copestang 1 291 09-05-2018, 09:11 PM
Last Post: Copestang
  LED light modification Danno 18 1,377 09-02-2018, 06:51 AM
Last Post: NOT A T5
Wrench brake light problem John J 3 288 08-24-2018, 08:51 PM
Last Post: John J
  clock and map light Copestang 14 566 08-14-2018, 10:22 AM
Last Post: Carolina_Mountain_Mustangs
  Brake light switch and wiring shaheenk 5 620 03-18-2018, 03:56 AM
Last Post: shaheenk
runninpony front signal light probs CWADAMS 1 375 01-04-2018, 01:03 PM
Last Post: Hemikiller



Users browsing this thread: 1 Guest(s)