• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
suspension change
#1
i plan on replaced the whole front end suspension, wonder is there  a order I should remove the parts in, ( Shocks Spring, spring saddle  Rotor swat bar link upper arm lower arm strut rod sway bar)?
  Reply
#2
Here's how I would do it:

Loosen/remove front nuts on strut rods
Spindle assemblies
Sway bar w/links
Shocks
Springs

The rest


  Reply
#3
I just tore down a 72 vert for parts over the winter. When guy wanted the front spindles for the PDB this is how i took apart.
I removed the shocks. Used spring compressor to compress the front spring and remove. This can be dangerous you have to compress around 4" if I recall. Once you get them out I suggest that you lay spring on ground outside and put a piece of plywood on the spring to remove the compressor. Had a friend that was using a impact wrench and got the screw so hot is seized and rotated the fingers in the spring clamp. They came off and the spring shot to the pavement and somehow did not take his fingers off. Hit the pavement and went over the entire shop building and landed in a field.
So after you get the spring out I would say the radius rods, then sway bar, then separate the ball joints and tie rods and get the spindles off and then you can remove upper and lower control arms.
Lots of dirty, greasy parts in there and of course some rust.
If you put a block of wood under the upper control arm and the frame rail where the red square is shown in the picture before you jack the car up it will save you some compression on the spring and will also keep the spring from bottoming out the shock. That is what destroys the rubber on the upper shock.
[Image: DSC00124.jpg]


When a man is in the woods and talks and no women are there is he still wrong??
Tongue
David
  Reply
#4
on lower arms take notice of where the oblong washer like are clocked and put them back the same way. the uppers might have lube points on the sides. lube before installing. with springs, the upper shock tower has 3 nuts to remove and u can use an inside spring compressor and let them hang. get new lower spring purchs too since u have everything torn apart. u can rent the inside spring compressor at auto zone. if doing steering arms do the measure to make sure u put back the same. with new stuff u'll need a front alignment and find one close for u will scrub the tires while driving. when u reinstall the springs have a 3rd hand close for it's really helpful to locate the lower part of spring.
  Reply
Share Thread:  


Possibly Related Threads...
Thread Author Replies Views Last Post
  Replacement Suspension Components ITMike5.0 6 156 09-30-2018, 10:06 AM
Last Post: ITMike5.0
  New suspension to build erikroy57 7 1,015 09-26-2018, 10:39 PM
Last Post: Spike Morelli
  rear suspension 71_resurrection 2 394 07-16-2018, 01:56 PM
Last Post: Hemikiller
  Ford Front Suspension Support Tool by Tommy Zees mustang7173 33 4,709 07-04-2018, 02:50 AM
Last Post: NOT A T5
  Air Suspension GeoBW 5 404 06-03-2018, 12:37 PM
Last Post: mudbilly
  Suspension issue jowens1126 10 1,091 03-11-2018, 07:52 PM
Last Post: jowens1126
  self made front suspension support tools eddyw 6 1,191 09-29-2017, 03:28 PM
Last Post: Hemikiller
  Suspension upgrade for this winter Robsweden 10 874 08-24-2017, 04:51 PM
Last Post: jowens1126



Users browsing this thread: 1 Guest(s)