• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Rear suspension upgrade
I am in the process of upgrading my rear suspension. I am installing a set of grab-a-trak 4.5 leaf springs with reverse eye (removing my 1” drop blocks) as well as a set of cal-tracks. I was planning on just using the stock rear shackles and some urethane bushings. I had been doing some research and saw some comments that I should not install a stock style bushing at the shackle when running the solid bushing up front that come with the cal-tracks. I found these and wanted some opinions if anyone has experience with this set up. 


I am basically trying to eliminate my lowering blocks, correct a bad wheel hop issue as well as a lack of traction issue.

73 Grandé H Code. Headman long tube headers, T-5 Transmission, 3.70 Traclok, Lowered 1" all around, Aussie 2v heads w/ 2.19 intake, 1.71 exhaust, screw in studs, full roller cam 608/612 lift 280/281 duration LSA 112, Quick Fuel 750 CFM double pumper, AirGap intake.

- Jason

[Image: 082-hot-rod-power-tour-2017-1970-1970s.jpg]
My .02 cents save the coin and stay with the stock shackles. I am running calvert springs and caltracs with stock shackles. Just run a good rear shock, I am running QA1s.
I am using the Maier Racing 4.5 leaf springs with Bilstein shocks and I am very happy with this setup. The suspension is firm but comfortable and the traction is amazing. With nearly 500hp and a Truetrac the traction is excellent when stepping on the gas. I am using a polyurethane bushing on front and normal rubber bushings at the shackle. Go to his website and read about it. They are expensive but with this setup you dont need Caltracs.

Sent from my SAMSUNG-SM-G930A using Tapatalk

[Image: 20160929_171923_edit2_small.jpg]

1971 M-Code Mach 1 w/Ram Air, 408 stroker, 285/291 0.558" roller cam, Blue Thunder intake, TKO600, Hooker headers with electric cut-offs, FiTech EFI w/ RobBMC PowerSurge pump
Strange center section with Truetrac, 3.5 gear and 31 spline axles, 4-wheel disc brakes
Depending on how serious you want to get with the bushings here is what we use to do.
I made aluminum bushings with a thin UHMW Ultra High Molecular Weight Polyethylene bushing next to the bolt to prevent squeak. I was a tool & die maker so easy for me to make them. Would also put the front half of main leaf spring on top going under the axle housing but not past the mount. Then made clamps to clamp the springs tight together. It for sure stopped wheel hop and improved handling for next to no cost.

When a man is in the woods and talks and no women are there is he still wrong??
Share Thread:  

Possibly Related Threads…
Thread Author Replies Views Last Post
  rear suspensions Mach 1 1973 Régis 4 231 05-03-2020, 04:52 PM
Last Post: Régis
  Rear disc conversion gap on install cwalker509 11 376 04-22-2020, 06:32 PM
Last Post: c9zx
  Rear end swap Scottyhudson 3 194 04-20-2020, 06:52 AM
Last Post: turtle5353
  Rear shock plate and shocks Kilgon 13 566 04-10-2020, 09:03 AM
Last Post: Kilgon
  Rear sway bar jpaz 29 2,092 04-09-2020, 12:03 PM
Last Post: Stanglover

Users browsing this thread: 1 Guest(s)