• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Rear Axle Housing Dimensions
#1
Does anyone have the width and side length of our rear axle housings?
From what I understand the total width is 61.25 from axle flange to axle flange, which ends up being 56.25 for the housing. However, does anyone know the length from the center of the pinion to each side's flange? I need these dimensions to order new axles. I am ordering a Truetrac differential as well. Apparently, the dimensions of the Truetrac are different than the open differential, which changes the each axle's length.

        [Image: 20160929_171923_edit2_small.jpg]

1971 M-Code Mach 1 w/Ram Air, 408 stroker, 285/291 0.558" roller cam, Blue Thunder intake, TKO600, Hooker headers with electric cut-offs, FiTech EFI w/ RobBMC PowerSurge pump
Strange center section with Truetrac, 3.5 gear and 31 spline axles, 4-wheel disc brakes
  Reply
#2
you mean b and c?
https://ibb.co/bt9caA

Used that image of a 9 inch for another thread, from all the picts I've found, they all displayed same values.
I'd double check tho as it's prolly rounded.

73 modified Grandé 351C. Almost done. 
71 429CJ. In progress
  Reply
#3
(11-21-2018, 07:04 PM)Fabrice Wrote: you mean b and c?
https://ibb.co/bt9caA

Used that image of a 9 inch for another thread, from all the picts I've found, they all displayed same values.
I'd double check tho as it's prolly rounded.
Yes, b and c.

Sent from my SAMSUNG-SM-G930A using Tapatalk

        [Image: 20160929_171923_edit2_small.jpg]

1971 M-Code Mach 1 w/Ram Air, 408 stroker, 285/291 0.558" roller cam, Blue Thunder intake, TKO600, Hooker headers with electric cut-offs, FiTech EFI w/ RobBMC PowerSurge pump
Strange center section with Truetrac, 3.5 gear and 31 spline axles, 4-wheel disc brakes
  Reply
#4
If I can engage the way back time machine I can see what I ordered up from Strange 11 years ago… I too have a true trac and fancy axles. I'll see if I can dig it up, but don't hold your breath.
  Reply
#5
(11-21-2018, 09:53 PM)Bentworker Wrote: If I can engage the way back time machine I can see what I ordered up from Strange 11 years ago… I too have a true trac and fancy axles. I'll see if I can dig it up, but don't hold your breath.
Thanks. I am ordering from Strange as well.
I will go to the garage and try to measure with some bob weights.

Sent from my SAMSUNG-SM-G930A using Tapatalk

        [Image: 20160929_171923_edit2_small.jpg]

1971 M-Code Mach 1 w/Ram Air, 408 stroker, 285/291 0.558" roller cam, Blue Thunder intake, TKO600, Hooker headers with electric cut-offs, FiTech EFI w/ RobBMC PowerSurge pump
Strange center section with Truetrac, 3.5 gear and 31 spline axles, 4-wheel disc brakes
  Reply
#6
(11-21-2018, 10:12 PM)tony-muscle Wrote:
(11-21-2018, 09:53 PM)Bentworker Wrote: If I can engage the way back time machine I can see what I ordered up from Strange 11 years ago… I too have a true trac and fancy axles.  I'll see if I can dig it up, but don't hold your breath.
Thanks. I am ordering from Strange as well.
I will go to the garage and try to measure with some bob weights.

Sent from my SAMSUNG-SM-G930A using Tapatalk

No dice.  I dug around in the folder of receipts and couldn't find anything.  Only thing I figured out was that I purchased Moser axles, not Strange.  As for dimensions they are long lost.
  Reply
#7
These are my measurements with a bob weight and ruler (pinion center to outside of axle flange):
Total L = 55 19/32 (55.59375")
Left side = 28 1/16 (28.0625")
Right side = 27 17/32 (27.53125")

Note: the measurements in Don's link are rounded lengths for the shafts, which are 31 3/4" and 27 13/16".

        [Image: 20160929_171923_edit2_small.jpg]

1971 M-Code Mach 1 w/Ram Air, 408 stroker, 285/291 0.558" roller cam, Blue Thunder intake, TKO600, Hooker headers with electric cut-offs, FiTech EFI w/ RobBMC PowerSurge pump
Strange center section with Truetrac, 3.5 gear and 31 spline axles, 4-wheel disc brakes
  Reply
Share Thread:  


Possibly Related Threads…
Thread Author Replies Views Last Post
  Axle advice needed kusanagi 13 428 09-10-2019, 03:02 PM
Last Post: kusanagi
  Rear diff oil change mustangandy 8 417 08-05-2019, 08:20 AM
Last Post: Don C
  Axle lengths dfayette 3 304 06-20-2019, 06:10 AM
Last Post: Manu Mach1
  rear end conversion don blanchard 5 478 05-08-2019, 06:13 AM
Last Post: turtle5353
  Regear Rear End icejawa 30 1,415 02-07-2019, 01:23 PM
Last Post: Hemikiller
  Recommended Rear End Ratio - 6 Speed TheDude 17 1,056 12-27-2018, 08:28 PM
Last Post: boilermaster
  rear end markc 6 606 10-14-2018, 12:24 PM
Last Post: markc
  my rear end is getting loose and making noise nailpounder 15 799 09-09-2018, 01:15 PM
Last Post: Don C



Users browsing this thread: 1 Guest(s)