• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Paint runs and dust nibs
#1
For those of us spray painting our own vehicles it is inevitable we will get some dust in the paint and no doubt most of us will get a run or two
There is nothing wrong with getting a run in the paint and from a well known local spray painter he reckons if you don't get a run every now and again you are not putting the paint on thick enough!

Anyway there are a few ways of removing these imperfections including applying fine body filler over the run then wet sanding the hell out of it or sanding the dust nibs with a tiny block and 1500 grit sandpaper or finer

Always looking for a better way I came across a relatively newer way of approaching this using a tungsten block so always looking for a better way I purchased a tungsten block receiving it today and couldn't help myself in at least giving it a shot.

Boy was I surprised at how easily it removed any blemishes but you do need to be careful with it
As much as I would like to take a video of my results I was lazy and have included a link here to a well made video
https://www.youtube.com/watch?v=dR4iKZvX53c
  Reply
#2
If i have a run that big, I tape off the area around it and then use a razor blade and scrape it in the same fashion he is doing in video. Wet sand it flush with 1,000 or 1,200. Then start stepping up the whole area around the run. I usually wet sand up to 2,500. I just wet sanded and de-nibbed the yellow mach 1 last night. Some areas I started at 1,500 that had some orange peel then stepped to 2000 then 2500. For the dust nibs I worked those with 2000 and made sure not to get anything in my paper while doing it. You don't want that dust nib sticking to your paper and making bigger scratches all over. Lots of different ways to tackle a run, but I never buy any special tools for it. Go slow and creep up on the run, tape off area around it and you will be fine. But that little tool looks like it works pretty good.

Kevin

1971 Mach 1
408C Stroker
C4 w/3,000 stall
8.8" Rear w/3.73's
Disc brakes all way around.

[Image: 28ivsix.png]




                                                                                             
  Reply
#3
$80.00 for a $5.00 piece of Tungsten Carbide is a little much. You can do the same thing with metal cutting tool inserts for lathe, mill and can even go to ceramic inserts. My aunt use to work at Kyocera Ceramics here where I live and if an edge did not clean up on the tool insert it was scrap since they were held to size within tenths of thousands of an inch. A triangle insert has six or eight cutting edges to use so if one if bad it is scrap. She would give me bags of them.
https://global.kyocera.com/prdct/tool/in...rthamerica
The edge on the ceramic is like a mirror finish the only thing that will cut it is diamond.
They make carbide paint scrapers I use when working on the home also. Their edge is not cut that that fine of a finish but you can lap with diamond compound.
Will have to see if it works on the paint runs.
I use to shave the paint off cars painted with lacquer with razor blades. was faster than stripper and less effort than sanding. It did not work as well on enamel paint.


When a man is in the woods and talks and no women are there is he still wrong??
Tongue
David
  Reply
#4
When I need fix a run or anything "too much" on a surface, I use the non cutting but sharp side of a cutter blade. If not sharp enough, I break for the next bit. I like I can hold it as a pencil and have precise control. I won't use a small tool like the one on the video for that reason.

73 modified Grandé 351C. Almost done. 
71 429CJ. In progress
  Reply
#5
There are a variety of crabide scrapers available that have handles, which would give you better control and not hide the area you're working on with fat fingers. An example, doesn't say it's for paint runs, but does say it's sharp:
https://www.amazon.com/Lisle-81780-Carbi...6704&psc=1



“If you can't explain it simply, you don't understand it well enough.”
--Albert Einstein
  Reply
#6
$80 USD is certainly a rip off. I paid about $45 USD and it comes with a handle with velcro so you can put a 1 inch sanding disc on it, this one -
https://www.ebay.com.au/itm/TUNGSTEN-BLO...SwQH5b23bl
Certainly an old razor works but best to sand the corners back a bit and no doubt many other ways to skin a cat but for me I can't help myself when a time saving gadget comes along to expand my ever growing tool collection.
  Reply
Share Thread:  


Possibly Related Threads...
Thread Author Replies Views Last Post
  which black paint for inner wheel arches baz70 8 339 02-05-2019, 04:21 PM
Last Post: baz70
  Stock Paint 73 mach 1 rjpohl 22 862 11-26-2018, 03:09 PM
Last Post: Hemikiller
  Prep underhood before paint andy72 4 292 11-22-2018, 10:40 AM
Last Post: SVO2SCJ
  Blackout hood paint jpaz 22 881 11-11-2018, 07:46 PM
Last Post: Stanglover
  Tail light black paint question vintageman 11 620 11-10-2018, 09:00 AM
Last Post: Carolina_Mountain_Mustangs
  What grit paper for stripping paint and rust??? scgamecock 3 333 10-27-2018, 08:22 PM
Last Post: Hemikiller
  What paint system did you go with? scgamecock 5 432 09-09-2018, 12:14 PM
Last Post: keiths71
  Black paint on Dynacorn Panels Ballaratcastle 12 938 08-16-2018, 04:46 PM
Last Post: piper62j



Users browsing this thread: 1 Guest(s)