• 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5
OK now I have an oil question
#1
I have a oil thing that bugs me. When the engine was built evry bearing was checked to keep 2 to 3 thousands clearence, now when I start it it has 65 to 70 psi pressure, but within about 5 minutes it drops to 45, if I hit the gas it jumps right back up.
So do you guys think I have a problem or just the wrong oil? currently running 20-40
  Reply
#2
PAPPY HAROLD;122342 Wrote:I have a oil thing that bugs me. When the engine was built evry bearing was checked to keep 2 to 3 thousands clearence, now when I start it it has 65 to 70 psi pressure, but within about 5 minutes it drops to 45, if I hit the gas it jumps right back up.
So do you guys think I have a problem or just the wrong oil? currently running 20-40

Normal operation. When the oil warms up, it thins out. This is the cause of the decrease in oil pressure. I like 20w-50, but you'll see about the same results.

[Image: 16ih3qg.png]
  Reply
#3
Nah! Your good.

[Image: 2rr7aiv.png]

Just cruising along minding our own business when BAM!!! The LAWS show up.
  Reply
#4
X3 good enough
The oil is a little thick for my taste, I like 10w-30. It flows a littke easier at cold temps.

Jeff T.

Low buck, touring style, '73 Convertible "rolling restoration", 351c, 2v heads with a shave and a haircut, Performer intake, Holley 650(ish), roller rockers, screw in studs, guideplates, stainless valves, Duraspark / Motorsports MSD, T-5 conversion. 1-1/8" front, 3/4" rear swaybars KYB shocks and some home brewed subframe connectors. Future plans; JGC steering box, Cobra brakes and... paint, interior, etc.

When I die I want to die like grandpa, peacefully in my sleep... not screaming, like his passenger.

[Image: 1_12_09_14_10_15_11.png]
  Reply
#5
I would drop her down to 10w30 but that's just me. I doubt you would see much difference in the oil psi though. I like to think the 10w30 will get throught the engine quicker on cold starts. depends on your climate though, if your not racing the engine and it's not constantly above 80* yet then i would stay away from anything higher than 40 weight.

Better to have higher pressure than lower pressure.
  Reply
#6
Dinosaur oil or synthetic?

Dino oil uses the lower viscosity rating and adds additives to it to get the higher viscosity rating. Meaning the take a 10 wt base oil mix in additives that bump it to 30, 40, 50 wt, etc.

Synthetic is just the opposite. They make the oil to be the higher viscosity as the base, say 40 wt, then put additives in to lower the viscosity to 10 wt.

Personally I use the lightest wt dino oil that still gives me good oil pressure. That oil is usually 5w-20 Valvoline dino oil. When running it hard and hot I still have good pressure so I'm good.

If I have low pressure, then and only then will I start bumping the viscosity up with each oil change until I have good pressure. Say 10w-30, then 10w-40. 10w-30 does the trick though in old, high mileage engines.

[Image: 386_07_10_13_5_58_42.jpeg]
My Mustangs:
71 M-code Mach 1, Medium Blue/White Sport, 4R70W, 3L50, Factory Ram Air.
72 Q-code Mach 1, Pewter/Black Sport, 4-spd, 3L25.
65 Convertible, Britney Blue/White/White, more modified than original.
05 Convertible, Legend Lime/Tan/Tan, future classic??
  Reply
#7
My builder specified a zinc added oil, said 10-30 or 10-40 is fine. I use valvoline VR1 10-30 and havent had a problem. I had some strange rhythmic vibration that got worse at higher rpm. Turns out my coil was failing and was losing spark as rpm rose. It became more obvious as time went on. With the new coil it runs great. The 10-30 is fine year round in the NE moderate climate and the hydraulic roller lifters and valve train has been running like a watch. Remember clevelands have been known to have difficulty getting oil to the crank under racing conditions so i figure 30 weight is better than a heavier weight. I do not have the moroso oil kit in my block.
  Reply
Share Thread:  


Possibly Related Threads...
Thread Author Replies Views Last Post
  Intake Cast Number Question kingb1973 7 548 09-08-2018, 08:27 AM
Last Post: kingb1973
  Axle question batwrangler 23 789 08-21-2018, 12:49 PM
Last Post: secluff
  SCJ Project car value and parts question atvdave 1 325 08-11-2018, 01:27 PM
Last Post: Don C
  '72 Sportsroof question soonerbillz 14 804 06-26-2018, 04:26 PM
Last Post: soonerbillz
  Rental Mustang question... soonerbillz 3 622 06-14-2018, 12:13 PM
Last Post: Boss1Ray
  Electrical Question mds1973 4 290 05-28-2018, 12:19 PM
Last Post: mds1973
  Another Marti report question: Steel Guard Rails? Mustangfeverrr 2 711 05-30-2017, 05:17 PM
Last Post: Mustangfeverrr
  1972 Mustang Convertible question Dcerny 8 1,005 04-15-2017, 07:43 AM
Last Post: Dcerny



Users browsing this thread: 1 Guest(s)