• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Oil pan question
#1
Hi All!

Recently I cleaned the undercarriage and engine with some Engine Brite. After that, I developed an oil leak at the dipstick tube where it enters the engine. I fixed that easily enough by taking out the tube, removing the old, cracked O ring and running a small bead of high temp. RTV where the dipstick meets the engine.

After that was cured, I developed another oil leak at the front passenger side corner of the oil pan. I could understand this because when I did my cam swap a while back, I had to lower the front of the oil pan and my gasket kit had two cheesy cork gasket pieces to put on the corners of the oil pan. Well, I used those gasket pieces with some high temp. RTV and they held for a while
but now one is leaking.

Anyway, I bought a nice rubber Felpro oil pan gasket and some more RTV and got busy taking the bolts off the oil pan (which, by the way, is some chrome after market pan). The pan may be a bit deeper than the stock pan because, when I do an oil change, It takes more than 5 quarts to fill it to the full line on the dipstick and this is after running the engine to fill the new oil filter.

To make a long story short. I can't drop the oil pan down far enough to clear the crank and slide it out. I thought about taking the two horizontal bolts out of the motor mounts and then jacking up the front of the engine by putting a block of wood under the harmonic balancer.

Does this sound like a bad idea to anyone? I'm only talking about jacking it up a little bit. Just enough to get the pan out. If anyone else out there has had this problem and came up with a simpler solution, I'm all ears.

Thanks in advance,

Jason

71 Mustang fastback
  Reply
#2
Jason
that's the way to do it. I've done that process many times to pull the pan. be sure and disconnect your battery to not cause any other issues.
  Reply
#3
Watch your transmission dipstick. Remove it before jacking up the engine or you'll risk bending the finger piece on the support that runs from the firewall to the shock tower. You may have to turn the crank to get the clearance when you drop it.

[Image: 2rr7aiv.png]

Just cruising along minding our own business when BAM!!! The LAWS show up.
  Reply
#4
We recently replaced the oil pan on my '71 Grandé M-code and had to jack up the engine.
In the process we found a broken motor mount so we replaced both of those.
The Ford shop manual says to remove the cross member (4 bolts) but mine is welded to the
frame. Also make sure your dip stick and holder are proper for the engine. I ordered a new
chrome dipstick, for cosmetic reasons, and discovered the dip stick I had was wrong for the
engine.

mike

[Image: 1_11_11_13_11_50_27.png]
  Reply
#5
I would also get rid of the chrome oil pan. I have tried 2 of them and had trouble with both of them.
Jim

drive it like you stole it
  Reply
#6
Be sure and watch your fan and shroud clearance. You should loosen the shroud and lift it out of it's clips so that the fan won't hit it.

[Image: 16kuyc0.jpg]
  Reply
#7

Thanks for the advice guys. I'll give it a try.

71 Mustang fastback
  Reply
Share Thread:  


Possibly Related Threads...
Thread Author Replies Views Last Post
  Toploader Crossmember Question Studdley 11 317 04-19-2018, 07:43 AM
Last Post: Studdley
  Oil change or not mpbsr 31 792 04-03-2018, 11:49 AM
Last Post: Hemikiller
  1972 351c oil pan repair BoweP 4 1,029 01-31-2018, 04:19 PM
Last Post: Ron Tanzi
  well liner question ? nailpounder 6 549 11-17-2017, 03:56 PM
Last Post: rackerm
  Starter Bolt Question Twins 24 1,195 10-08-2017, 06:29 PM
Last Post: Twins
  Fuel line question for 72 Q-code eventhorizon 5 662 10-06-2017, 08:30 AM
Last Post: Stanglover
  Power steering pump ERUPTION! [Update question] Sumit 37 3,763 07-31-2017, 12:46 PM
Last Post: Stanglover
  A/C question jowens1126 14 970 07-25-2017, 02:01 PM
Last Post: Pegleg



Users browsing this thread: 1 Guest(s)