• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Looking for 351cleveland Edlebrock SVO intake
#1
Thought I would post here since there are a lot of cleveland guys here.

I’m rebuilding my 351 4v, and I have one of the M-9424-A351 Roush/ Ford intakes that has been machined to work on my epoxied 4v heads. pic attached.
I don’t like that this particular model requires a turkey pan.

I’m looking for one of the EDLEBROCK “Torker” versions that has the solid floor pan base.

If you have one you would be willing to sell, please contact me.
Mike
832-833-0893




Sent from my iPhone using Tapatalk
  Reply
#2
What about one of the Edelbrock Performer series intakes for the 351C?  They come in both 2V and 4V flavors, and share similar dimensions to the factory intake manifolds (i.e., won't mess with Ram Air component clearances).

Eric

[Image: mach1sig2.gif]
  Reply
#3
That is certainly an option.
Was just hoping to find a hi port option similiar to what I already have except with the floor pan.

Here is what I have.
The PO riveted a sheet metal bottom on it.
[Image: 735e52191e7f823ca22b7303416694db.jpg][Image: 16e870bc720ca82fee0c75cee8698031.jpg]


Sent from my iPhone using Tapatalk
  Reply
#4
I saw one on craigslist the other day. $150

https://pittsburgh.craigslist.org/pts/d/...81862.html

Kevin

1971 Mach 1
408C Stroker
C4 w/3,000 stall
8.8" Rear w/3.73's
Disc brakes all way around.

[Image: 28ivsix.png]




                                                                                             
  Reply
#5
Awesome.
Trying to buy it.
Sent communication.



Sent from my iPhone using Tapatalk
  Reply
#6
Actually upon further inspection, that one is a bit different.
This in the one I’m looking for.
[Image: 6071fa040a850cf39cb6962026d86aea.jpg]


Sent from my iPhone using Tapatalk
  Reply
#7
Well I just found this one.....


[Image: 7bdc3bc147171a205d41f429dfb1e6f5.jpg]


Sent from my iPhone using Tapatalk
  Reply
#8
Wow - so, you have a hole in your hood I take it?   Cool

Eric

[Image: mach1sig2.gif]
  Reply
#9
Unfortunately I do....
Previous owner did it.
Not much I can do about it now.
I am going to put a different scoop.
The current one is butt ugly.


[Image: 393f13a30a16a169a5bcae368344b47c.jpg]


Sent from my iPhone using Tapatalk
  Reply
#10
(05-10-2019, 11:30 AM)mikeyhunts Wrote: Actually upon further inspection, that one is a bit different.
This in the one I’m looking for.
[Image: 6071fa040a850cf39cb6962026d86aea.jpg]


Sent from my iPhone using Tapatalk

I have one, it is powered coated gray.  I'll see if I can get a pic if you are interested.

-john
(jbojo)
351C 4V cc heads, 10.5 : 1 CR, 290 Herbert cam, Flat top forged pistons, forged connecting rods, Atomic efi,
C6 with Gear Vendor overdrive, 3.89 Tru Trac, Hooker Super Comp with 2 1/2" Pypes Exhaust.        

Some Mod pictures can be seen at:

  Reply
Share Thread:  


Possibly Related Threads…
Thread Author Replies Views Last Post
  Intake Swap Omie01 5 270 07-01-2019, 08:16 AM
Last Post: jpaz
  New fuel line after intake and carb change. klinton994 3 259 05-24-2019, 07:58 PM
Last Post: c9zx
  Intake alignment dowel removal help Phats 5 273 04-15-2019, 01:36 PM
Last Post: Jeff73Mach1
  Intake sucking air and not in a good way! scgamecock 15 532 03-24-2019, 10:47 AM
Last Post: scgamecock
  Intake valley pan, reuse it??? scgamecock 12 942 03-08-2019, 12:27 AM
Last Post: Spike Morelli
  Are these the right gaskets for head and intake? scgamecock 4 264 02-20-2019, 11:34 AM
Last Post: Carolina_Mountain_Mustangs
  1971 351C 2V Intake and carb question. turtle5353 42 1,917 01-12-2019, 09:13 AM
Last Post: Ron Tanzi
  Intake have to be on for a compression check? scgamecock 9 646 11-15-2018, 09:17 PM
Last Post: barnett468



Users browsing this thread: 1 Guest(s)