• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Justin's 1973 Mach 1 "Q" Code
#21
Well guys after tearing down the Cleveland down we found multiple issues. The guy that put the motor together had failed to torque multiple main and rod bolts. The 4MA crank was .030/.030 but seemed freshly cut. It does have new H555CP pistons and the bores are fresh accept the condensation flash rust from sitting up for years. The rod bolts will need to be changed to ARP. Needless to say I am glad we tore it down.
I picked up some parts from Craigslist. I paid $400 for a 4 bolt 351C block .030, a set of large valve 4V heads, the heads came with Crane stud conversion installed, and Comp 1.73 roller rockers. Along with the sale I got a Summit billet distributer, Moroso valve covers, Comp .080 wall chromoly push rods, and Eddy Torker intake. Yeh most of which will be sold to purchase needed parts.
I also recently purchased a 4MAB STD/STD crank from a guy in Detroit for $150. Eddie, the guy in Detroit, actually has more STD/STD cranks in his collection he wants to sell.
Please tell me what you think about the proposed build below for the daily driven 1973 Mach 1 for my son's first car. I know some will not like the 73 4V heads but I have been instructed by a few Cleveland guys that the small valves will actually help performance down low for daily driving and cruising.

Engine Plan: 357C w/9.25:1 compression (daily driven 350-375hp build?)
.030 block (decked .025)
4MAB STD/STD (fully polished and prepped)
D0AE rods with ARP fastners
Sealed Power H555CP flat top pistons
Balance rotating assembly
D3AE 4V open chamber heads
- Ferrea valves 2.08/1.65
- Crane Stud Conversion
- Comp Cams 1.73 roller rockers
- New guides, springs, locks, retainers, and seals
- .010 surface cut (possibly more depending on CC after polishing chambers)
- polish combustion chambers (help prevent detonation)
Howards Street Force 2 camshaft kit
-215/225 @ .050, 269/279 advertised, 513/536 lift, ICL 106, LSA 112
-1600-5400 RPM
Edelbrock Performer RPM Air Gap intake
Self learning EFI system (FiTech, EZ EFI, Holley sniper)

Exhaust Plan:
Hooker 4v headers w/1.75" or 1.875" primaries
Pypes stainless 2.5" mandrel bent exhaust

Transmission Plan: Non Electronic AOD for Fox body Mustang
AOD wide ratio conversion to 4R70W gears
2000-2200 stall
(Justin's car has 3.25 gearing with track lock)
  Reply
#22
Great project

Sendt fra min F8331 med Tapatalk

So I'm a proud owner of one Mach 1 73! Regards Lars DK73whistling
  Reply
#23
(12-21-2016, 12:55 PM)wrobinson Wrote: I ordered the Deluxe Marti Report today. I think the Ivy Glow paint and Avocado interior might be somewhat unique but we will see. Ivy Glow/C4 paint was new for 1973. I guess we will wait and see.

Im in the same boat, friend.
4C - Ivy Glow Paint
GG - Avocado Interior


1949 Ford F1 Truck
1951 Studebaker 2R5 Truck
1956 Chevrolet 3100 Truck
1967 Chevrolet Camaro
1968 Oldsmobile Toronado
1969 Chevrolet El Camino
1969 Ford Torino GT
1971 Mercury Cougar XR7
1973 Ford Mustang Mach 1
1974 Dodge Charger Hardtop
1975 Ford Maverick Superluxo
1977 Ford Maverick GT


  Reply
#24
A month or so ago my son and I started removing components to ready the car for the body shop.
[Image: IMG_0758.jpg]

[Image: IMG_0761.jpg]

[Image: IMG_0762.jpg]

[Image: IMG_0763.jpg]

[Image: IMG_0764.jpg]
  Reply
#25
A month or so ago my son and I started removing components to ready the car for the body shop.
[Image: IMG_0758.jpg]

[Image: IMG_0761.jpg]

[Image: IMG_0762.jpg]

[Image: IMG_0763.jpg]

[Image: IMG_0764.jpg]
  Reply
#26
The car loaded up and headed to the body shop to replace the quarter panel.
[Image: IMG_0788.jpg]

[Image: IMG_0789.jpg]
  Reply
#27
The car loaded up and headed to the body shop to replace the quarter panel.
[Image: IMG_0788.jpg]

[Image: IMG_0789.jpg]
  Reply
#28
Quarter panel removal.
[Image: IMG_0806.jpg]

[Image: IMG_0807.jpg]
  Reply
#29
I have gathered engine components together for the 351 4V build. I have acquired a STD/STD 4MAB crankshaft, ARP rod bolts, Crane stud conversion kit, Comp roller rockers, Comp chromoly push rods, ARP head bolts, 2.08/1.65 Ferrea 5000 valves, and H series rod/main bearings.
[Image: IMG_0693.jpg]

[Image: 615.jpg]


[Image: 616.jpg]
  Reply
#30
Not sure where you are in the Southeast. but I just removed a nice clean gas tank from my car to fit a fuel cell. I won't ship, I can't deliver, but if you are close to Nashville, I will give it away.

[Image: 1_01_07_15_8_53_18.png]

"I love my Hookers!" and "Get some Strange" probably have a different connotation to non automotive enthusiasts!
  Reply
Share Thread:  


Possibly Related Threads...
Thread Author Replies Views Last Post
  Summer deadline - 72 Mach 1 Build thread baz70 59 1,714 7 hours ago
Last Post: Pegleg
  71 Grabber Green Metallic M code convertible Richard Verco 27 710 04-18-2019, 09:39 PM
Last Post: Richard Verco
  71 Euro Shelby (Mach 1) Clone whelessray 3 125 04-16-2019, 04:17 AM
Last Post: NOT A T5
  Have started the long job of cleaning the 73 Mach 1 Carolina_Mountain_Mustangs 120 4,779 04-15-2019, 08:52 PM
Last Post: mjseakan
  Video of 73 Mach 1 going into MOM Carolina_Mountain_Mustangs 13 328 04-15-2019, 09:55 AM
Last Post: Carolina_Mountain_Mustangs
  Yellow Mach 1 is back again! turtle5353 191 4,626 04-15-2019, 06:11 AM
Last Post: turtle5353
  Dragging restoration of my 72 Q code! scgamecock 2 152 04-10-2019, 11:10 PM
Last Post: mach71351c
  MuscleTang mod project thread (1971 M-Mach 1) tony-muscle 256 27,061 03-08-2019, 08:13 AM
Last Post: tony-muscle



Users browsing this thread: 1 Guest(s)