• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Front Bumper 1973
#1
Hi

Just about to mount my front bumper. Have had it off for painting. It`s in two pieces now. The rubber part that is being repainted and the steel part. I took it away in one piece but when I mount it back, should I do it in the same way? Or first mount the steel part and then the rubber part? Would be good to know. Regards Dalis.
  Reply
#2
(01-20-2019, 01:13 PM)Dalis Wrote: Hi

Just about to mount my front bumper. Have had it off for painting. It`s in two pieces now. The rubber part that is being repainted and the steel part. I took it away in one piece but when I mount it back, should I do it in the same way? Or first mount the steel part and then the rubber part? Would be good to know. Regards Dalis.

I took all the steel pieces out, cleaned, neutralized all the rusty bits then re-painted chassis black.  Chased the all the threads and pre - assembled it to make sure it was O K then tighten up when you're happy.


When all back together, it is heavy ( as you already know ) so be careful with the flexible ends as the paint will crack.  I set mine up on two boxes close to the correct position left & right then got a floor jack under it to lift into place.  Careful, careful - don't drop it now.


This will allow you to reach the four remaining bolts behind the mounting brackets and get them started.  Get each one in a few threads and pull them tight when it's all lined up with the lower fenders.  There is a fair bit of adjustment with the slotted bracket holes so you can align it correctly.  Same with the fender to lower valance positioning - you might need to loosen these up to get final alignment. Took me half a day to get it reasonable.
Go for it.
PKJ
[+] 2 users Like 6DUB606's post
  Reply
#3
I took help of my two strong sons, took about a half on hour to remount it. Looks fine now. Thanks for support in the tread.
  Reply
#4
Hi! How I can take off that rubber skin from bumper metal parts? I take off those bolts under the bumper but the cover dosent't come out.
  Reply
#5
(03-31-2019, 02:59 PM)Aris Wrote: Hi! How I can take off that rubber skin from bumper metal parts? I take off those bolts under the bumper but the cover dosent't come out.

By " under the bumper " are you referring to the licence plate bracket ? or the bolts that hold the steel frame to the urethane section ?

There are a couple of access holes in the main steel frame.  Way up inside these are  ( 4 ? ) bolts that attach the urethane part to an inner mounting plate.  You will need a long extension to reach these.  Spray some CRC or similar penetrant on them and give it time to work.
All kinds of sneaky things to provide more challenges.
PKJ
[+] 1 user Likes 6DUB606's post
  Reply
#6
There are 4 nuts o  the inside of the metal frame. You need a socket extension to get to them.

Edit: I should have read PKJ's previous post. He nailed it.

[Image: 73-Mustang-Front-Bumper-Bracket.jpg]


[Image: 20141019-123516-1.jpg]
....
[+] 1 user Likes rackerm's post
  Reply
#7
(03-31-2019, 07:15 PM)rackerm Wrote: There are 4 nuts o  the inside of the metal frame. You need a socket extension to get to them.

Edit: I should have read PKJ's previous post. He nailed it.

[Image: 73-Mustang-Front-Bumper-Bracket.jpg]


[Image: 20141019-123516-1.jpg]
....

HI! Thank you. So there was more bolts inside the bumper... 

Thankyouyellow goodpost
  Reply
Share Thread:  


Possibly Related Threads…
Thread Author Replies Views Last Post
  Trunk mat for 1973 Mach 1? Dalis 4 189 11-17-2019, 09:16 AM
Last Post: Dalis
  Trunk paint color shade for 1973 Mustangs timachone 8 311 11-11-2019, 02:36 PM
Last Post: 7173Vert
  Center Console shifter Plate Assembly 1971-1973 mustang7173 3 256 10-22-2019, 02:01 PM
Last Post: RC92234
  front bumper options? Danno 6 321 10-16-2019, 11:16 AM
Last Post: 1sostatic
  Front and Rear Seat Rebuild mustang7173 10 762 08-02-2019, 10:25 AM
Last Post: Carolina_Mountain_Mustangs



Users browsing this thread: 1 Guest(s)