• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Front brakes not locking up
#1
Some time ago I replaced the brakes at the four corners. In the front I installed Wilwood's 11.3" rotor kit with 4-piston calipers (140-13477). In the rear I installed a conversion kit that uses the ElDorado type of rear brake calipers. Recently, I replaced the master with a Wilwood tandem (260-8555) with a 1" bore. All the tubing and hoses are new. I also have a proportioning valve on the rear circuit. That said, everything has been replaced except the combination valve. However, I rebuilt the combination valve with the kit from Muscle Car Research and removed the integrated proportioning valve springs of the combination valve. My issue is that the car is not braking as I was hoping it would. With the proportioning valve all closed I am able to lock the rear brakes, but I have not been able to lock the front brakes. I expected that with the brake system that I have I should have been able to lock up the front brakes. I understand that I don't actually want to lock the front brakes for efficient braking, but the fact that I am not able to lock them when fully stepping on the pedal is telling me that something is not right. The only suspect I have now is the combination valve and I am wondering if I should eliminate it and go with a tee to the front. What else can be in the combination valve that could cause the front brakes to be inefficient or am I missing something? I guess that the only thing I will lose is the functionality of the idiot brake light.

        [Image: 20160929_171923_edit2_small.jpg]

1971 M-Code Mach 1 w/Ram Air, 408 stroker, 285/291 0.558" roller cam, Blue Thunder intake, TKO600, Hooker headers with electric cut-offs, FiTech EFI w/ RobBMC PowerSurge pump
Strange center section with Truetrac, 3.5 gear and 31 spline axles, 4-wheel disc brakes
  Reply
#2
Hi

Did you benchbleed the new master cylinder ? Im suspecting air is trapped somewhere. Did you push the pads to far back when installing them ?

For knowing your limit you have to pass it thumb
  Reply
#3
Air trapped sounds indeed like the bad guy as the kind of brakes you have installed should send you straight into your windshield if pressed to the max.
Did you noticed if the car wanted to go one side when you tried?

How did you bleed the lines? Personally, I do the expensive way, meaning, I use way more fluids than I should.
I usually set a plastic tube down a container pre filled where the tube hole is submerged, then put my wife to work, per side (first passenger then driver side) pumping fast, 4 or 5 times and then hold, close bleeder a tad, so I can refill the MC level, repeat till no air is seen in the tube, and on the final pass, while the brake pedal is under max load, I tighten te bleeders. Usually, the container, is then holding 1/4 quart per line and when done, end up with more liquid used than I should have, but totally sure to have 100% clean/new fluid and no air.

73 modified Grandé 351C. Almost done. 
71 429CJ. In progress
  Reply
#4
I forgot to add that yes, I did bench bleed the MC. I actually bled it for a lot of reps even after there were no bubbles. I did bleed the brakes but it is very possible that I am not being successful on taking all the bubbles out. Something that bothers me about the system is that the loop of the tubing as it comes out of the MC is higher than the MC. Because of the loop, I can see it very easy for bubbles to get trapped at the top of the loop and expect that these bubbles won't travel too easily out of the system. That's why at some point I was asking if reverse bleeding would be more effective in getting rid of bubbles in the loop. These bubbles will have to somehow travel around the loop, then through the combination valve through the ups and downs of the tubing to the bleeder and out.

        [Image: 20160929_171923_edit2_small.jpg]

1971 M-Code Mach 1 w/Ram Air, 408 stroker, 285/291 0.558" roller cam, Blue Thunder intake, TKO600, Hooker headers with electric cut-offs, FiTech EFI w/ RobBMC PowerSurge pump
Strange center section with Truetrac, 3.5 gear and 31 spline axles, 4-wheel disc brakes
  Reply
#5
I would suggest two things

1. test the pressure at the calipers as your system is set and see what pressures you are getting. If you don't want to buy the tool, shoot me a pm and I'll ship you mine for the cost of shipping.

2. Consider your pad compound. When I had ceramic pads on my front brakes, they just didn't get hot enough to perform. Semi metallic pads returned the braking to what I expected.

[Image: 1_01_07_15_8_53_18.png]

"I love my Hookers!" and "Get some Strange" probably have a different connotation to non automotive enthusiasts!
  Reply
#6
(04-29-2019, 11:17 AM)Jeff73Mach1 Wrote: I would suggest two things

1. test the pressure at the calipers as your system is set and see what pressures you are getting.  If you don't want to buy the tool, shoot me a pm and I'll ship you mine for the cost of shipping.

2. Consider your pad compound.  When I had ceramic pads on my front brakes, they just didn't get hot enough to perform.  Semi metallic pads returned the braking to what I expected.

1. Thank you Jeff. I will PM you.
2. The pad compound is the BP-10 from Wilwood which is supposedly recommended for Street High Performance. They have a compound with slightly better CF but I don't think this will be the big difference I am looking for. I am sure I could improve the rear's pad for a better one, but that won't help the fronts.

        [Image: 20160929_171923_edit2_small.jpg]

1971 M-Code Mach 1 w/Ram Air, 408 stroker, 285/291 0.558" roller cam, Blue Thunder intake, TKO600, Hooker headers with electric cut-offs, FiTech EFI w/ RobBMC PowerSurge pump
Strange center section with Truetrac, 3.5 gear and 31 spline axles, 4-wheel disc brakes
  Reply
#7
While you wait for the pressure tool,
if you have high lines, just pomp fast, air doesn't travel as fast as in water in brake fluid. Bubbles will be flushed by the incoming fluid. 4 or 5 times and hold it (your pumping friend that is). The bleeders, don't open them too much so you can just secure them in 1/4 turn to refill.
Did you also have the tube in fluid so no air can return or do you have one of these bleeders valve?

73 modified Grandé 351C. Almost done. 
71 429CJ. In progress
  Reply
#8
(04-29-2019, 01:28 PM)Fabrice Wrote: While you wait for the pressure tool,
if you have high lines, just pomp fast, air doesn't travel as fast as in water in brake fluid. Bubbles will be flushed by the incoming fluid. 4 or 5 times and hold it (your pumping friend that is). The bleeders, don't open them too much so you can just secure them in 1/4 turn to refill.
Did you also have the tube in fluid so no air can return or do you have one of these bleeders valve?

I can try with 4-5 times. I have been using 1 pump of the pedal since from what I read, there is a school of thought that if you pump too many times you end up breaking the bubbles in more tiny bubbles. For the first time during the bleeding process the tube is in air and it eventually starts filling up with fluid. Since I shut the bleeder before my helper releases the pedal it shouldn't matter, right?

        [Image: 20160929_171923_edit2_small.jpg]

1971 M-Code Mach 1 w/Ram Air, 408 stroker, 285/291 0.558" roller cam, Blue Thunder intake, TKO600, Hooker headers with electric cut-offs, FiTech EFI w/ RobBMC PowerSurge pump
Strange center section with Truetrac, 3.5 gear and 31 spline axles, 4-wheel disc brakes
  Reply
#9
That's why I do the expensive way. bubbles, tiny bubbles, micro bubbles, they all go using plenty fluid Smile
You will see them in the tube (I use transparent one). make sure also that you open enough usually 1/4 from the point its loose to max 1/2 allows a great flow and a quick way to lock for refill. The pumping 3-5 times fast ( fast as my wife can pump ) and holding works for me every time. On my bikes always did same too and could tilt rear wheel up.

73 modified Grandé 351C. Almost done. 
71 429CJ. In progress
  Reply
#10
(04-29-2019, 02:14 PM)Fabrice Wrote: That's why I do the expensive way. bubbles, tiny bubbles, micro bubbles, they all go using plenty fluid Smile
You will see them in the tube (I use transparent one). make sure also that you open enough usually 1/4 from the point its loose to max 1/2 allows a great flow and a quick way to lock for refill. The pumping 3-5 times fast ( fast as my wife can pump ) and holding works for me every time. On my bikes always did same too and could tilt rear wheel up.

It is a good workout too Big Grin

        [Image: 20160929_171923_edit2_small.jpg]

1971 M-Code Mach 1 w/Ram Air, 408 stroker, 285/291 0.558" roller cam, Blue Thunder intake, TKO600, Hooker headers with electric cut-offs, FiTech EFI w/ RobBMC PowerSurge pump
Strange center section with Truetrac, 3.5 gear and 31 spline axles, 4-wheel disc brakes
  Reply
Share Thread:  


Possibly Related Threads…
Thread Author Replies Views Last Post
  Front Coil Spring Perch Tab AOCUSNRET 6 267 08-07-2019, 08:29 AM
Last Post: Don C
  1973 mach 1 351 cleveland rear brakes Nige 9 332 07-29-2019, 06:04 PM
Last Post: Don C
  Rear brakes hanging up. turtle5353 2 180 07-13-2019, 04:45 PM
Last Post: turtle5353
  Front coil springs vintageman 18 1,091 06-27-2019, 01:37 PM
Last Post: vintageman
  Front Shock Size Parkka 2 211 06-24-2019, 06:31 AM
Last Post: Parkka
  Front Suspension Bang raeovine 14 752 06-05-2019, 09:55 AM
Last Post: Carolina_Mountain_Mustangs
  do your brakes lock up nailpounder 6 398 05-08-2019, 09:33 PM
Last Post: Spike Morelli
  Front power brakes factory or not Nige 2 321 05-04-2019, 08:04 AM
Last Post: Carolina_Mountain_Mustangs



Users browsing this thread: 1 Guest(s)