• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
From the top: ‘73 Q code convertible
#1
And in the beginning... (btw, a forum dedicated to our own builds/restos is such a great idea - thanks)

Introductions have been made in the New Users forum, so this is my rebuild/resto thread.  My goal is an original-as-possible sweet “weekend cruiser” with only the few modernizations that are more or less essential to dependable driving (i.e., I never ever want to have to adjust points again — my absolute nemesis!). I plan to work my way through (in this order) 1) dependable, 2) comfortable, 3) attractive up to awesome ride.

The car arrived yesterday so I got my first thorough unattended inspection.  No complaints about the seller; it was a quick & efficient transaction and the description was thorough and accurate, however... it’s always the ‘what they don’t say’ you have to look for.

My first impression?  “Welcome home, beautiful!” (Seller’s photos)


[Image: 83660-FDE-D396-4-FB6-A237-38-B6089620-D3.jpg]

[Image: 28-D5-EFA1-91-C9-4-A5-B-B1-F3-0-B28-A7653-B7-C.jpg]


And now reality.
Exterior:  “par” for 46 year old car not maintained beyond the essentials.  2nd paint job was crap.  Several small trim pieces (hood locks, side panel “Mustang” script) missing.  Def needs a new top (knew that) but the top mechanicals are *excellent*.  Endless body tweaks and adjustments needed. Floor pans and trunk, solid other than (known) dime size hole in passenger rear trunk well.  More troublesome: that “little scrunch” on the driver rear corner will probably necessitate a quarter panel replacement.

Being the first year for the 5 mph bumper mandates, I expected they’d seen punishment.  That said, front bumper looks pretty good although it seems a bit set back:  the urethane attached to the bumper for the sides that covers the gap to the fender overlaps onto the fender by about 1/2” — can the bumper just be adjusted back out?

Under the hood: Seller replaced air, oil and fuel filters, all the fluids, battery, coil, voltage regulator and upper/lower radiator hoses.  It’s good because I would have done that anyway, but not good because the old fluids are a good diagnostic. P/s pump leaks (a lot) — no fluid even showing on the dipstick — but when the engine is running, works fine(?).  But I can’t really take it our for spin until... the leaky radiator is fixed (has been ordered and yes, I’m staying with copper/brass and upgrading to 3-row).

But... lots of “ponderables”.  Why is the oil dipstick coming up under the a/c compressor rear hoses?  Not near, “in”.  What were they thinking with that hose that’s about a foot too long (can’t yet say what the hose is for, but it hangs down 3”-4” under the engine).  And “Hey, you:  ya left one of your sockets attached” (I remember the excruciating effort to get up in there with my ‘71 many moons ago and then when extracting my wrench, the socket stayed behind.  But I never left one.)

With engine running:  starts *nearly* flawlessly *nearly* every time!  And then the fun begins... A few misfires until it gets warmed up but then purrs smoothly.  However, exhaust smells way too rich and idle never drops below 1k.  After getting to normal temp a few revs (hold at 2500) reveals:  stumbles on the way up, say at 1500-2000 rpm as if it were getting too much fuel, but then surges beyond that.  If you’re holding 2-2500 rpm and just take your foot completely off the accelerator: spin down to full stop and off (dead).  A slow release of the pedal and it just returns to idle.  I will be inspecting every vacuum tube under the hood I can find today.

Underneath:  cursory inspection.  Old undercoating needs to be removed/replaced, but it’s really done it’s job.  No rust other than expected surface dust.  Rear end does not leak. No oil/fluids coming out of unusual places.

Interior: Ulpholstery and carpet def ready to be replaced.  But workable as is for now. Dash cracked (meh, not dreadful.  Add to the list).  Passenger and driver seats were switched so that will eventually go back (as is, the seat back release levers are on the side furthest from the door), console is in good shape except the console liner/bin has part of the bottom cut out for who know’s what) and inside, first owner-added “what does this switch do?” . Instrument lenses clear!  Uh, who knows how to get that mess of a horn working — without replacing the wheel? (see photo).  All major switches work as do the power windows (passenger’s needs new cam, but you can hear the motor purring as it tries.  Bueno). Wipers work and park perfectly, but alas, no washer.

HVAC:  well... compressor known as not working, but, controls mostly ok.  Fan speed good.  Air to a/c vents and floor vents fine, except hi “Hi/Lo” (no mixing; all upper or all lower).  On “Heat” it should send most air to the floor, next position over, mix floor and defrost, on Defrost, full output to windshield.  Seems we are at “Mix and Full Defrost” only.  Maybe some jammed doors, or missing/broken vacuum hoses.


Radio:  “silent”.  Either not getting power, or dead; TBD.  Console clock:  same.

Nighttime inspection:  all exterior lights good except for one side marker lamp.  High/low work (but oh my do those headlight need to be aimed).  Interior courtesy lights all working (not many in a ‘vert), but... no dash or console lighting.

Which led to this morning, crawling under the dash, to see what I might see, regarding the dash and console lighting and radio power.  What.  A.  Hornet’s.  Nest.

So many splices! And a new “what does this do?” switch.  Fuses in the fuse block a-ok, so about the radio, there must be an in-line fuse somewhere... or something is just completely unattached.

There you have it.  I have about a grand worth of parts on order — so while I wait, I’ll be here reading up on “disassembling the instrument panel and center console”.

And yes, since this is a (hopefully) ongoing thread of my project and progress, any of your $.02 you want to throw in along the way would be welcomed.
  Reply
#2
Sounds like you did okay for the closing price. Rust can be a huge expense on a convertible and with such a nicely optioned car, you're ahead of the game.  I'll tackle stuff in order on your post.

Quarter- a good body shop can pull that quarter and make it right, probably no need to cut into the car. 

Front bumper - yes, they can be adjusted and I've seen more than one with a pile of shims between the bumper and the absorber. 

P/S - seal kit for the pump is about $10 and quite easy to install, once you get the pump out. Get some Type F ATF in there before it hurts the pump. At this age, the whole system will probably need to be rebuilt/resealed. Hoses are cheap and readily available, the box comes out pretty easy and there are places that do the rebuilds.

Dipstick - that the heater hoses it's threading through, use a longer hose when you replace them to push them out away from the dipstick. The big black rectangular hose is the outside air duct. It pulls cool air from below the engine compartment. Looks like it was replaced at one time and never trimmed to length. 

Engine - guessing you have the original Autolite 4300D. It's known to be a bit "cantankerous". 

Interior - carpet - be sure to get the Mass Backed option, it fits much better. Looks like there's something going on with the passenger seat, might have a broken weld internally. 

Horn - horn pad and all the parts are available reproduction. The whole pad comes off with two phillips heads from the rear and has a couple wires with pusch-on terminals on the wheel. 

https://www.npdlink.com/1965-1973-mustan...al-2-spoke


HVAC - selector has a vacuum switch known to fall apart. A fairly easy fix once you get there. 

Radio - fused only at the fuse block. Might be disconnected behind the dash. Clocks are known to burn out. 

To get you started - 1973 wiring diagrams are attached below.


Attached Files
.pdf   1973_full.pdf (Size: 7.81 MB / Downloads: 10)


[+] 2 users Like Hemikiller's post
  Reply
#3
Thanks! Yes, given what I've seen since, I think I got a fair enough price for far from perfect but a nearly perfect features/options in overall decent condition.

The "a good body shop can..." part is a huge relief. It was going to be a "have to be later thing" anyway as I'd want to do that the same time as a repaint. The underlying yellow (6E) isn't bad, but the black stripes, especially on the hood are a mess. All that's for after I get it running & driving dependably. I did get Type F fluid for the steering pump nearly immediately. I'm fairly certain I'll be taking your tip for restoration.

Sort of like the horn: ya look at it and think "what a mess" but then after you step back and someone sprinkles some sanity around, it's not so bad.

Given the (old) a/c is not working, and eventually I'll upgrade to R134a and that changes out the hoses, is there any reason not to pull the compressor now and just leave it out? Having more room to work under the hood even if temporary would be nice.

And my hope, once I get behind the dash, is to find the radio was just disconnected for whatever reason. The most intriguing thing will be chasing down what the two owner-added switches are four since I can't find any extra equipment (fog lights, for example). There's one cheesy switch inside the center console and another decent switch mounted just to the left of the radio, toward the back.

Again, thanks for the tips!
  Reply
#4
OH! Forgot: the wiring diagrams you attached are 100% more readable than the set I have. Many thanks.
[+] 1 user Likes RC92234's post
  Reply
#5
You can remove the pump, it has it's own belt, so removing it and the upper sheetmetal bracket won't hurt anything. If you want to remove the big cast iron lower mount, you need to put a spacer behind the power steering pump bracket.

[Image: 73ac.jpg]


[+] 1 user Likes Hemikiller's post
  Reply
#6
Nice car. 73 Q code convertibles are fun to drive and to repair. Make sure you have the right  battery cables and a electronic voltage regulator. They will prevent you from having a lot of issues in the future.


John J
[+] 1 user Likes John J's post
  Reply
#7
Ah... morning discoveries under the air filter assembly.

Sure, doesn’t everyone plug a vacuum hose with an old screw? ?
[Image: 8-A392554-B50-F-449-A-8269-2-B24-DABB7-FAB.jpg]

[Image: 2525-E547-938-F-4-C20-8-A5-F-84-FBE43-B6-D0-F.jpg]

[Image: 16-B7-F194-90-DC-443-C-BCA7-8-DE67-C472-B7-A.jpg]

[Image: 68-EE6975-CE65-46-AA-B070-F18-B0-D714-FDB.jpg]
  Reply
#8
Looks like the previous owner was in the "as long as it works" category wanna-be mechanic. That little section of fuel hose was just a fire waiting to happen, especially with that uninsulated glob of solder not far away.

Now you'll get to scratch your head (until you're as bald as me) wondering what/why did they do that? Smile

It looks like you have a car that's in overall decent shape to begin your journey with, though. Good luck with making the car yours.



“If you can't explain it simply, you don't understand it well enough.”
--Albert Einstein
[+] 1 user Likes Don C's post
  Reply
#9
A different angle on the carb/fuel filter.  What is this gunk at the top?  It's hard, like a solder.  Also looks like part was ground off then dunked over.  *head scratcher*

More concerning, have they done something to the inlet that makes this carb ineligible for a resto?

[Image: IMG-6142.jpg]
  Reply
#10
(06-29-2019, 01:27 PM)RC92234 Wrote: A different angle on the carb/fuel filter.  What is this gunk at the top?  It's hard, like a solder.  Also looks like part was ground off then dunked over.  *head scratcher*

More concerning, have they done something to the inlet that makes this carb ineligible for a resto?

[Image: IMG-6142.jpg]
Looks like some type of epoxy was used to "fix" a fuel leak.

73 conv. 460, D0VE large valve heads, Performer RPM manifold, Voodoo 227/233 cam, Holley 950 HP carb, C6 trans, 3.25 trak-loc.
  Reply
Share Thread:  


Possibly Related Threads…
Thread Author Replies Views Last Post
  My 71mach M code 72mach351 6 614 09-15-2019, 05:47 PM
Last Post: 72mach351
  71 Grabber Green Metallic M code convertible Richard Verco 27 1,198 04-18-2019, 09:39 PM
Last Post: Richard Verco
  Dragging restoration of my 72 Q code! scgamecock 2 356 04-10-2019, 11:10 PM
Last Post: mach71351c
  Justin's 1973 Mach 1 "Q" Code wrobinson 45 5,902 02-22-2019, 03:12 PM
Last Post: wrobinson
  My 72 Q code conv Boss1Ray 46 5,380 10-23-2018, 03:02 PM
Last Post: Boss1Ray
  1996 Mark VIII drive train into a 1973 Convertible wandmbowles 8 1,942 10-07-2018, 10:32 PM
Last Post: FordRamAir.com
runninpony 27 Years since my last Mustang ! - 72 Convertible Build Thread 724me 9 629 10-07-2018, 11:59 AM
Last Post: 73pony
  1971 Mustang Convertible - Code Name: Burn Victim AMWeaver47 43 7,167 08-02-2018, 06:43 AM
Last Post: AMWeaver47



Users browsing this thread: 1 Guest(s)