• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Ford 302 Main Cap bolts
#1
Wrench 
Hi,

Looking for Main Cap bolts for my 1972 Mustang,
one of them broke when installing.

Will those be ok:

https://www.ebay.com/itm/NOS-NEW-1962-19...:rk:1:pf:0


Or does any one here have some for sale ?

Thanks
  Reply
#2
That is the correct main cap bolt for 68 thru 79 302 engines.

You might want to verify that your torque wrench is accurate before proceeding with anymore assembly.

I'd probably just spring for a set of ARP main bolts and replace the lot.

https://www.summitracing.com/parts/arp-1.../make/ford


  Reply
#3
runninpony 
+1 what Hemikiller said, buying on Epay you might end up with lower quality!

71-73 Mustangs never die, they just go faster!
  Reply
#4
Stang1972, meant to respond to your inquiry last night but the internet was down again, so here goes this morning!
You do have to watch out on E-Bay.  Most are great and trusted sellers, but there are some that would stick junk (especially hard to ID bolts and hardware) in a Ford box and sell for premium prices.
The cost of the two bolts you are looking at plus shipping just to a US address @ $22.09 is a lot of money for what you would be receiving. Plus you would have to factor in actual shipping costs  to your location.
Ford used the C2OZ-6345-A  main bearing cap bolt from 1962 (221-260-289 engines) through 2001 when the last 302's (called ThunderJets) were production installed in the 2001 Explorer. The 93-95 SVT Mustang Cobra 5.0 used TTY (Torque to Yield) head and main bearing cap bolts. These TTY bolts were used as service replacements as the original C2OZ were discontinued. Unless an original owner that is familiar with the repair history of your engine, I would take HemiKiller's wise advice and replace all the bolts with the ARP bolt set. The job of the main cap bolt is too critical to risk reusing old original "Tired" bolts or where someone has used some TTY bolts which I only feel safe using once.
Good Luck on your project.       Smile

Steve

No Officer...I really don't know how fast I was going, my speedometer stopped at 140!
[+] 1 user Likes secluff's post
  Reply
#5
+1 on what has already been said, get new reliable source fasteners. I suggest burnishing all new critical fasteners (by torquing loosening, and retorquing 3 times before final torquing) and using a consistent high pressure lube such as CMD High Pressure Lube #3. Chuck
  Reply
Share Thread:  


Possibly Related Threads...
Thread Author Replies Views Last Post
  73 302 ro 351w swap now transmission noise samckay 7 164 01-13-2019, 01:01 PM
Last Post: Hemikiller
  302 engine identification & specs rjpohl 5 143 01-10-2019, 08:22 PM
Last Post: Hemikiller
  71 vert dual exhaust, longtube header, 302 2V, reinforcement torque plate 1971V8 11 478 09-29-2018, 09:53 AM
Last Post: c9zx
  71, 302 engine gauge feed wiring misterjason 2 361 09-18-2018, 10:28 AM
Last Post: misterjason
  E7TE 302 Heads piper62j 3 517 08-17-2018, 08:00 AM
Last Post: piper62j
  Water Pump mounting bolts EBSTANG 2 445 07-23-2018, 08:33 PM
Last Post: turtle5353
  302 headers with manual trans Daves73 12 665 07-11-2018, 01:26 PM
Last Post: Don C
  Performance Part 302 engine Cresee 7 630 05-12-2018, 06:12 PM
Last Post: Ed Raver



Users browsing this thread: 1 Guest(s)