• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
[For Sale] Rear axles (2 sets) - 9" Ford
#1
I have two pairs of rear axle (left and right) for sale, including installed bearings. The first pair came with the car and had a measured runout of about 0.015" at the flange (0.004" at the axle). The second pair I bought used from Don (OMS). Those had a runout of 0.004" when I measured a year and half ago. None of these axles exhibited perceptible vibrations at highway speeds of 80+ MPH.
This is a thread I started discussing the axles: https://www.7173mustangs.com/thread-axle-flange-bent.

Cost: $75. Each axle has bearings pressed that were used no more than 1,000 miles. I think I still have the outer flanges as well, which I will include. Edit: the flanges are not mounted though.

        [Image: 20160929_171923_edit2_small.jpg]

1971 M-Code Mach 1 w/Ram Air, 408 stroker, 285/291 0.558" roller cam, Blue Thunder intake, TKO600, Hooker headers with electric cut-offs, FiTech EFI w/ RobBMC PowerSurge pump
Strange center section with Truetrac, 3.5 gear and 31 spline axles, 4-wheel disc brakes
  Reply
#2
Are they 28 or 31 spline? That info would help.

[Image: 1_01_07_15_8_53_18.png]

"I love my Hookers!" and "Get some Strange" probably have a different connotation to non automotive enthusiasts!
  Reply
#3
(01-15-2019, 09:39 AM)Jeff73Mach1 Wrote: Are they 28 or 31 spline?  That info would help.

Excellent question. They are Ford original 28 spline.

        [Image: 20160929_171923_edit2_small.jpg]

1971 M-Code Mach 1 w/Ram Air, 408 stroker, 285/291 0.558" roller cam, Blue Thunder intake, TKO600, Hooker headers with electric cut-offs, FiTech EFI w/ RobBMC PowerSurge pump
Strange center section with Truetrac, 3.5 gear and 31 spline axles, 4-wheel disc brakes
  Reply
#4
Did I read that correct you pressed new bearings on but did not put the flange on? Humm that is not good, lol.


When a man is in the woods and talks and no women are there is he still wrong??
Tongue
David
  Reply
#5
(01-15-2019, 06:11 PM)Carolina_Mountain_Mustangs Wrote: Did I read that correct you pressed new bearings on but did not put the flange on? Humm that is not good, lol.

The disc brake kit has "open" flanges that you can install after the fact. If you needed the OEM flanges installed then yes, the bearings will have to be removed.

Look at the flanges in this picture. They are open.

[Image: right-stuff-rear-contents-red-calipers.jpg]

        [Image: 20160929_171923_edit2_small.jpg]

1971 M-Code Mach 1 w/Ram Air, 408 stroker, 285/291 0.558" roller cam, Blue Thunder intake, TKO600, Hooker headers with electric cut-offs, FiTech EFI w/ RobBMC PowerSurge pump
Strange center section with Truetrac, 3.5 gear and 31 spline axles, 4-wheel disc brakes
  Reply
#6
(01-15-2019, 06:42 PM)tony-muscle Wrote:
(01-15-2019, 06:11 PM)Carolina_Mountain_Mustangs Wrote: Did I read that correct you pressed new bearings on but did not put the flange on? Humm that is not good, lol.

The disc brake kit has "open" flanges that you can install after the fact. If you needed the OEM flanges installed then yes, the bearings will have to be removed.

Look at the flanges in this picture. They are open.

[Image: right-stuff-rear-contents-red-calipers.jpg]
I see said the blind man.


When a man is in the woods and talks and no women are there is he still wrong??
Tongue
David
  Reply
#7
Here is a picture of one set of axles. The other is still in the rear end.


[Image: 20190115-122619.jpg]

        [Image: 20160929_171923_edit2_small.jpg]

1971 M-Code Mach 1 w/Ram Air, 408 stroker, 285/291 0.558" roller cam, Blue Thunder intake, TKO600, Hooker headers with electric cut-offs, FiTech EFI w/ RobBMC PowerSurge pump
Strange center section with Truetrac, 3.5 gear and 31 spline axles, 4-wheel disc brakes
  Reply
Share Thread:  


Possibly Related Threads…
Thread Author Replies Views Last Post
runninpony 73 Rear Floor Pans $25 each + S&H MNMustang73 0 106 09-01-2019, 11:47 PM
Last Post: MNMustang73
  2 rear quarter panels not2old 0 225 07-14-2019, 06:54 PM
Last Post: not2old
runninpony 1972 Ford Mustang Convertible madmusclegarage 3 344 07-07-2019, 06:41 AM
Last Post: jpaz
  Ford Racing Cleveland valve covers ZIPNZ 0 227 05-21-2019, 09:58 AM
Last Post: ZIPNZ
runninpony 71 Currie 9” crate 9” rear end 71StangNC 5 637 05-05-2019, 07:56 PM
Last Post: Newold
  1973 Grandé Rear Window Exterior Trim detritusmaximus 0 184 03-20-2019, 12:24 AM
Last Post: detritusmaximus
  1973 Coupe interior rear panels detritusmaximus 2 282 03-19-2019, 11:29 PM
Last Post: detritusmaximus
  [FOR SALE] Used Ford Performance Parts Cleveland Aluminum Valve Covers M-6582-Z351 Bentworker 0 396 03-02-2019, 02:18 PM
Last Post: Bentworker



Users browsing this thread: 1 Guest(s)