• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Engine/dyno/speed programs
#1
A bunch of years ago I had a computer program that allowed you to enter specifics about an engine build, sometimes even by manufacturer, that would let you enter different components and then estimate HP/Torque results. Then it would take your numbers and estimate 1/4 mile times and top speeds based upon the aerodynamics of the specific car that you were working with. At the time I was building an engine for a 68 shelby gt 500 and the program was within 20 HP/Torque ratings of the actual dyno results. I found the program to be remarkably accurate as it said 1/4 mile times were N/A due to lack of traction and top end was estimated to be 180+mph. I never acheived that top end speed due to lack of nerve on my part but at 150 the car was still pulling strong and had over 1000 rpm left before redline. 

Unfortunately, this was maybe 3-4 computers ago and I didn't save this particular program.  Any similar programs out there that are fairly accurate?
  Reply
#2
(02-02-2019, 10:09 PM)mbrew2 Wrote: A bunch of years ago I had a computer program that allowed you to enter specifics about an engine build, sometimes even by manufacturer, that would let you enter different components and then estimate HP/Torque results. Then it would take your numbers and estimate 1/4 mile times and top speeds based upon the aerodynamics of the specific car that you were working with. At the time I was building an engine for a 68 shelby gt 500 and the program was within 20 HP/Torque ratings of the actual dyno results. I found the program to be remarkably accurate as it said 1/4 mile times were N/A due to lack of traction and top end was estimated to be 180+mph. I never acheived that top end speed due to lack of nerve on my part but at 150 the car was still pulling strong and had over 1000 rpm left before redline. 

Unfortunately, this was maybe 3-4 computers ago and I didn't save this particular program.  Any similar programs out there that are fairly accurate?

may be this site can help you

[Image: wracetxt9.jpg]
  Reply
#3
Comp cams has an estimator. Requires Flash Player
http://www.camquest.com/

You can also download a copy of it
http://www.compcams.com/downloads/register.asp



“If you can't explain it simply, you don't understand it well enough.”
--Albert Einstein
  Reply
#4
Dynomation, Performance Trends, and Pipe Max are reasonable accurate but require a lot of real data to be accurate and the software is not inexpensive. Chuck
  Reply
Share Thread:  


Possibly Related Threads...
Thread Author Replies Views Last Post
  Headers to fit '72 Mach 1 w/400 engine MeanMachine 8 291 04-14-2019, 06:38 AM
Last Post: MeanMachine
  basic engine temps SteveO_71 5 197 04-05-2019, 04:00 PM
Last Post: tony-muscle
  Post your burbling bit (Engine) 1sostatic 7 356 03-26-2019, 10:26 AM
Last Post: 1973machi
  Engine breakin oil question EvilPuppetMaster 10 297 03-25-2019, 09:36 PM
Last Post: EvilPuppetMaster
  Got my rebuilt Hurst 4 speed shifter back. Stanglover 24 733 03-19-2019, 12:05 PM
Last Post: Stanglover
  351C 4V - 72 Mach 1 Engine fan baz70 16 587 02-21-2019, 09:13 AM
Last Post: Stanglover
  302 engine identification & specs rjpohl 5 326 01-10-2019, 08:22 PM
Last Post: Hemikiller
  Recommended Rear End Ratio - 6 Speed TheDude 17 614 12-27-2018, 08:28 PM
Last Post: boilermaster



Users browsing this thread: 1 Guest(s)