• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
efi pump mount location
Hi guys
I bought used fitech EFI 600 hp system with inline fuel pump.
can someone tell me what is the common mount location for fuel pump and pre-filter on 71-73?
manual states that pump and pre-filter must be placed as low as the lowest point of the tank and within 2 feet away from it.

Bottom of my fuel tank is way below any frame mounting points so I have no idea where to mount it
any suggestions?
For my sniper, had to build a bracket/casing for the pump.


73 modified Grandé 351C. Almost done. 
71 429CJ. In progress
Here's what I did with my Holley inline pump.  It'll be feeding an Edelbrock E-Street high-pressure pump/reservoir ahead of the EFI itself.  Right now, it's doing a phenomenal job keeping the 600cfm Performer carb happy.

I mounted it up inside the rear wheel well - there's space between the inner wheel house and actual rear frame rail (unless you're tubbed, that is).
[Image: attachment.php?aid=34693]

Also made a rock shield for it out of someone's left over under-shroud.  I found it after someone changed their oil at the Auto Hobby Shop and threw it away.

[Image: attachment.php?aid=34694]

I'm also using the standard fuel sending unit/pick-up inside the tank.

Hope this helps.


[Image: mach1sig2.gif]
I already have electric low pressure pump hooked up at the rear frame rail however it is above the bottom of the fuel tank

I might have to fabricate something to suspended new efi pump below frame rail so it is closer to the bottom of the tank
Thanks for ideas
I was thinking a good place to mount the Fuel Commander is where the blue emissions can went. You won't need it with EFI, so Its a nice spot for that.

[Image: can.jpg]

"I drank what?" - Socrates
(01-02-2019, 02:07 PM)jowens1126 Wrote: I was thinking a good place to mount the Fuel Commander is where the blue emissions can went. You won't need it with EFI, so Its a nice spot for that.

[Image: can.jpg]
Thats exactly where i placed my sump pump. I have Robbmc's one. I used the vent hose as a return hose. You can see my thread for all the details. I dont have a link right now.
Things to keep in mind:
-You may want to drill the vent port at the top of the fuel tank to allow for free flow of fuel if using it as a return line. I adapted an old sending unit to replace the vent port. These sump pumps return little fuel through the return line compared to a standard fuel pump. On that thought you have to allow venting of the tank. In my case is through the filler cap.
-I insulated the bottom of the fuel pump tank to protect it from the heat of my headers. I did this even though my headers are ceramic coated.
-Use a pre filter and post filter.
-I added a fuse between the EFI unit and the pump.

        [Image: 20160929_171923_edit2_small.jpg]

1971 M-Code Mach 1 w/Ram Air, 408 stroker, 285/291 0.558" roller cam, Blue Thunder intake, TKO600, Hooker headers with electric cut-offs, FiTech EFI w/ RobBMC PowerSurge pump
Strange center section with Truetrac, 3.5 gear and 31 spline axles, 4-wheel disc brakes
The tank still needs to be vented, as does the Fuel Command Center.

“If you can't explain it simply, you don't understand it well enough.”
--Albert Einstein
My question was regarding inline fuel pump not efi command center....

Good info btw. I might have to go that route if I cant find good location for inline fuel pump
Share Thread:  

Possibly Related Threads…
Thread Author Replies Views Last Post
  PS Pump priming kingb1973 11 344 08-06-2019, 12:01 PM
Last Post: Fabrice
  EFI fuel tank 73' mach 1 21 704 07-22-2019, 08:45 AM
Last Post: 73' mach 1
  Water Temp sender in water pump - 351C TheDude 34 1,360 06-11-2019, 08:06 PM
Last Post: TheDude
  Holley sniper efi system andresde71 6 570 06-04-2019, 03:21 PM
Last Post: mikeyhunts
  Ignition resistor location jowens1126 5 233 05-22-2019, 04:36 PM
Last Post: jowens1126
  Holley Sniper EFI HyperSpark Distributor Kit 73' mach 1 5 435 04-29-2019, 05:15 PM
Last Post: mikeyhunts
  351C EFI don blanchard 13 998 04-28-2019, 11:01 PM
Last Post: detritusmaximus
  Fuel Pump Parkka 5 352 03-27-2019, 12:22 PM
Last Post: Parkka

Users browsing this thread: 1 Guest(s)