• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
driveshaft oem parts
#1
i am looking at replacing my driveshaft and associated parts. these are the part numbers i have found for 1972 with 351c with FMX; drive shaft D1ZZ-4602-C (2 3/4 x 51 3/32)...yoke C3AZ-4841-A 31 spline...Front U-joint C3AZ-4635-E....Rear U-joint C3AZ-4635-F. i dont see a different number for different body type. I am considering going with an aluminum driveshaft since the prices arent much different and i dont have more than 500HP. Any comments by anyone who has had experience with driveshaft replacement is welcome. Suppliers, alum vs steel, u-joint sizes, and yoke manufacturers/materials are of interest. looking at the bigger suppliers like Inland and Denny's. And how in the world can a driveshaft be installed off center in the yoke?
  Reply
#2
wwhite72;165494 Wrote:i am looking at replacing my driveshaft and associated parts. these are the part numbers i have found for 1972 with 351c with FMX; drive shaft D1ZZ-4602-C (2 3/4 x 51 3/32)...yoke C3AZ-4841-A 31 spline...Front U-joint C3AZ-4635-E....Rear U-joint C3AZ-4635-F. i dont see a different number for different body type. I am considering going with an aluminum driveshaft since the prices arent much different and i dont have more than 500HP. Any comments by anyone who has had experience with driveshaft replacement is welcome. Suppliers, alum vs steel, u-joint sizes, and yoke manufacturers/materials are of interest. looking at the bigger suppliers like Inland and Denny's. And how in the world can a driveshaft be installed off center in the yoke?
G-
Save your money..If you come up as we discussed we will find your issue within an hour or two..I can take your driveshaft to the same place I had mine done..They will replace the u-joints balance it's 10 minutes from my place..It cost me 90.00 with everything..I had it the next day after it was dropped off.. I will be taking my aluminum one there after the 4r70w is installed.

LOVE OF BEAUTY IS TASTE..THE CREATION OF BEAUTY IS ART
  Reply
#3
so you like alum? Im always looking for ways to take weight off the car.
  Reply
#4
wwhite72;165528 Wrote:so you like alum? Im always looking for ways to take weight off the car.
Not really but it's what the P.O. had installed when he did the 429 big c-6 conversion So I have it & it should be close length wise so I'm going to use it..If I had to buy one I'd be looking for used in a junk yard..

LOVE OF BEAUTY IS TASTE..THE CREATION OF BEAUTY IS ART
  Reply
Share Thread:  


Possibly Related Threads…
Thread Author Replies Views Last Post
  AC Compresssor Parts to sell kcmash 2 130 05-22-2020, 10:18 PM
Last Post: Kilgon
  351 Cleveland engine parts and worth 501MACH1 11 1,375 10-17-2018, 09:38 AM
Last Post: Carolina_Mountain_Mustangs
  408 Stroker parts discussion tony-muscle 62 6,761 10-14-2018, 10:59 PM
Last Post: tony-muscle
Wrench Engine Parts Farmer 2 557 09-18-2018, 09:47 AM
Last Post: Carolina_Mountain_Mustangs
Wrench Engine Parts Farmer 2 495 09-17-2018, 05:11 PM
Last Post: NOT A T5



Users browsing this thread: 1 Guest(s)