• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Dash harness
#1
Have any of you ever experienced a warm under dash harness or any harness that becomes warm to the touch?
All grounds are good and clean and when I installed the headlights, the turn signals in front won’t blink
When I remove the actual headlights, they work. All this and the harness wires are warm. Any suggestions will be greatly appreciated.
  Reply
#2
There are anywhere from 2 to 3 resistor wires buried in the underdash harness. When operating, they will cause it to be warm to the touch, but not hot.
1. Coil resistor wire runs from fuse box to either tach plug or back of the fuse box. Always on when key is in RUN position.
2. Alternator indicator lamp resistor wire: only works when bulb is broken.
3. Dash cluster CVR input resistor wire: runs from back of wiper switch to dash cluster connector. Always in operation. Will become hot (not warm) if CVR output gets grounded.

Let me check your shorts!
http://midlifeharness.com

[Image: Flamicon2.jpg]


[Image: oldfart.png]
[+] 1 user Likes midlife's post
  Reply
#3
Light conflicts are generally caused by bad grounds, from housings to ground, wires to ground, or bulb bases not making good contact with the socket. All grounds have to be to bare metal, paint is a good insulator. The battery ground has to be connected to the chassis at the voltage regulator and the engine block.

Electricity seaks whatever path has the least resistance, whether it is direct or through other circuits. Bad grounds can cause all kinds of weird symptoms as they loop through other circuits.



“If you can't explain it simply, you don't understand it well enough.”
--Albert Einstein
  Reply
#4
I hate electricity cannot they make it mechanical?


When a man is in the woods and talks and no women are there is he still wrong??
Tongue
David
  Reply
#5
(04-12-2019, 07:23 PM)midlife Wrote: There are anywhere from 2 to 3 resistor wires buried in the underdash harness.  When operating, they will cause it to be warm to the touch, but not hot.  
1. Coil resistor wire runs from fuse box to either tach plug or back of the fuse box.  Always on when key is in RUN position.
2. Alternator indicator lamp resistor wire: only works when bulb is broken.
3. Dash cluster CVR input resistor wire: runs from back of wiper switch to dash cluster connector.  Always in operation.  Will become hot (not warm) if CVR output gets grounded.

Thanks for the info!
  Reply
#6
(04-12-2019, 07:57 PM)Don C Wrote: Light conflicts are generally caused by bad grounds, from housings to ground, wires to ground, or bulb bases not making good contact with the socket. All grounds have to be to bare metal, paint is a good insulator. The battery ground has to be connected to the chassis at the voltage regulator and the engine block.

Electricity seaks whatever path has the least resistance, whether it is direct or through other circuits. Bad grounds can cause all kinds of weird symptoms as they loop through other circuits.

Thnx will check all ground points
  Reply
#7
(04-13-2019, 01:45 AM)IURmach1 Wrote:
(04-12-2019, 07:23 PM)midlife Wrote: There are anywhere from 2 to 3 resistor wires buried in the underdash harness.  When operating, they will cause it to be warm to the touch, but not hot.  
1. Coil resistor wire runs from fuse box to either tach plug or back of the fuse box.  Always on when key is in RUN position.
2. Alternator indicator lamp resistor wire: only works when bulb is broken.
3. Dash cluster CVR input resistor wire: runs from back of wiper switch to dash cluster connector.  Always in operation.  Will become hot (not warm) if CVR output gets grounded.

Thanks for the info!
  Reply
#8
Well, my mechanic worked it all out
He had to substitute the backup switch part of that harness with another switch because the bracket had no mounting point but the four plug mated correctly at the firewall

He replaced the turn signal switch harness and it corrected the brake light issue. I adjusted the switch under the dash previously and had brake lights on the driver side and the new TS switch did the trick

The headlight issue was resolved when he checked the wires on the after market lights and fixtures. They were crossed from the factory so he swapped them and now they work in conjunction with the front turn signals...

Hope this info helps
  Reply
Share Thread:  


Possibly Related Threads...
Thread Author Replies Views Last Post
  73 Mach 1 dash wiring DeereFanatic 4 185 03-30-2019, 10:32 AM
Last Post: Carolina_Mountain_Mustangs
  dash speaker jackf 3 218 03-26-2019, 03:53 PM
Last Post: jackf
  Factory tach and center gauges without changing harness? TheDude 16 888 01-07-2019, 09:28 PM
Last Post: midlife
  Tach and dash wiring/lights project rjpohl 4 388 01-04-2019, 05:18 PM
Last Post: rjpohl
  dash wire left to right kick panel rjpohl 1 281 11-21-2018, 07:36 PM
Last Post: Don C
  Under dash wiring harness routing 73429mach 5 628 09-03-2018, 07:14 PM
Last Post: 73429mach
  Dash Circuit Board digithead 4 623 08-30-2018, 06:48 AM
Last Post: digithead
  72 dash clock pete w 1 335 08-29-2018, 06:08 AM
Last Post: TheRktmn



Users browsing this thread: 1 Guest(s)