• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Apiller
#1
Does anyone know of anyone make an A piller guage pod for a 71 mustang. I would like them where I can see them and put my center A/C vent back where it belongs instead of on the shelf.Huh
  Reply
#2
I have never seen one for our mustangs.Not to say that they don't.I would like to see one.
[Image: 20r9ylt.jpg]
  Reply
#3
Would a universal pod work?
Jeff T.

Low buck, touring style, '73 Convertible "rolling restoration", 351c, 2v heads with a shave and a haircut, Performer intake, Holley 650(ish), roller rockers, screw in studs, guideplates, stainless valves, Duraspark / Motorsports MSD, T-5 conversion. 1-1/8" front, 3/4" rear swaybars KYB shocks and some home brewed subframe connectors. Future plans; JGC steering box, Cobra brakes and... paint, interior, etc.

When I die I want to die like grandpa, peacefully in my sleep... not screaming, like his passenger.

[Image: 1_12_09_14_10_15_11.png]
  Reply
#4
Don't know. I tried Auto Meter in Sycamore,Il and they couldn't tell me anything.
Jim
  Reply
#5
Never seen one myself. Seems I looked once upon a time and gave up, to many other things to worry about. But prob could take a universal one like was said and graft it onto your piece. If you go that route make two and send me one Tongue

http://www.amazon.com/Universal-60mm-Tri...B001PL9KHM
  Reply
#6
Thinking about universal 1 issue that rises in my mind is getting the proper angle.
Jeff T.

Low buck, touring style, '73 Convertible "rolling restoration", 351c, 2v heads with a shave and a haircut, Performer intake, Holley 650(ish), roller rockers, screw in studs, guideplates, stainless valves, Duraspark / Motorsports MSD, T-5 conversion. 1-1/8" front, 3/4" rear swaybars KYB shocks and some home brewed subframe connectors. Future plans; JGC steering box, Cobra brakes and... paint, interior, etc.

When I die I want to die like grandpa, peacefully in my sleep... not screaming, like his passenger.

[Image: 1_12_09_14_10_15_11.png]
  Reply
#7
(12-28-2010, 03:39 PM)coilwire Wrote: Does anyone know of anyone make an A piller guage pod for a 71 mustang. I would like them where I can see them and put my center A/C vent back where it belongs instead of on the shelf.Huh

Not to hard to make your own just time consuming ! If i wasn't so involved in my 72 project
http://www.saturdaymorninggarage.com/


I would make it for you...Heres a link on the general concept.
http://www.mp3car.com/vbulletin/fabricat...r-pod.html

Scott

LOVE OF BEAUTY IS TASTE..THE CREATION OF BEAUTY IS ART
  Reply
#8
Nice article.
Jeff T.

Low buck, touring style, '73 Convertible "rolling restoration", 351c, 2v heads with a shave and a haircut, Performer intake, Holley 650(ish), roller rockers, screw in studs, guideplates, stainless valves, Duraspark / Motorsports MSD, T-5 conversion. 1-1/8" front, 3/4" rear swaybars KYB shocks and some home brewed subframe connectors. Future plans; JGC steering box, Cobra brakes and... paint, interior, etc.

When I die I want to die like grandpa, peacefully in my sleep... not screaming, like his passenger.

[Image: 1_12_09_14_10_15_11.png]
  Reply
#9
Just found out Just Dashes make a dash pad with the guages built into the center of the pad facing the driver.Am going to call the after the 1st to confirm. Tad expensive $600.
Jim
  Reply
#10
Going to have to find some cheap a pilers and try that.
  Reply




Users browsing this thread: 1 Guest(s)