• 1 Vote(s) - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5
351 engine tear down
#81
(03-28-2016, 08:03 AM)Manu Mach1 Wrote: So, still need camshaft bearings:
Sealed Power 1403M or Clevite SH710S.

Rod bearings:
Sealed Power 83400CP or 3400CP.
0,010 undersize.

Crankshaft main bearings:
Sealed Power 4925M or 146M.
0,010 undersize.

The bypass tube is already removed, pinhole on it, need a new one.

Any though about what I should choose?

Here is the block before and after a cleaning job:

On those main bearings, At our shop, we stock the Clevite bearings, and, they are very good bearings. For use with the stock cast iron crank, I'd stick with the "P" series, which are standard 77 material. The "H" series means hardened, and likely not necessary with a soft crank , still, a good bearing. Personally, I like, (and run in my Mach and my Ford powered ski flatbottom boat ), the Sealed Power "M" series, like the 146M noted above. The 146M bearings are a competition bearing material, and are 3/4 grooved sets, that is, unlike the Clevite set which has a fully grooved upper shell in the block and a non-grooved lower shell for load carrying, the 146M sets have an upper fully grooved and a lower which has partial grooves close to the halves parting line giving more oil available to supply the rod bearings but solid bearing material at the bottom where the most load is concentrated.
The Sealed Power 3/4 groove design is of the very same design used in modern performance engines today, notably the Chevrolet LS series being but just one of those utilizing this 3/4 groove technology.
That heater hose nipple is always something we will replace whenever we are working on a customer's block. They are pressed in to the block. Often, they are so damaged or rusty that removing the darned thing takes some patience, but not a big deal. Most auto parts stores have the nipple listed in their heater/ air conditioning parts books. Also, when cleaning the block, have your shop remove the oil galley plugs, front and rear, and have them rifle-brush those passageways clean. Note, that the front allen plugs are a special thread and are slighty "pointy" on their back side. DON'T misplace or loose these, as they are special to the front oil galleys behind the timing gear. Just a little thing, but nobody has mentioned that difference in the galley plugs thus far. 
  Reply
#82
(05-08-2019, 07:15 PM)c9zx Wrote: That is correct on both counts. Chuck

Thanks. So for the moment I keep the stock distributor and later will see with ignition conversion kit.

Mustang, beer and rock'nroll
  Reply
#83
Look up Pertronix. They have some nice electronic ignition products.

"I drank what?" - Socrates
  Reply
Share Thread:  


Possibly Related Threads...
Thread Author Replies Views Last Post
  Boss 351 PCV Hoses kcmash 8 266 05-12-2019, 08:51 AM
Last Post: Hemikiller
  351 c starting issues kcmash 44 775 04-27-2019, 07:24 PM
Last Post: c9zx
  351 cleveland oil pan gasket Nige 8 296 04-19-2019, 07:40 AM
Last Post: kcmash
  Headers to fit '72 Mach 1 w/400 engine MeanMachine 8 345 04-14-2019, 06:38 AM
Last Post: MeanMachine
  basic engine temps SteveO_71 5 246 04-05-2019, 04:00 PM
Last Post: tony-muscle
  Hagerty Article on the 351 Cleveland 1973_Mustang_Conv 2 254 04-01-2019, 05:24 PM
Last Post: donkost
  351 Cleveland Oil Restrictors – 351C Oiling Fix Boss1Ray 5 510 03-31-2019, 09:35 AM
Last Post: Carolina_Mountain_Mustangs
  Post your burbling bit (Engine) 1sostatic 7 380 03-26-2019, 10:26 AM
Last Post: 1973machi



Users browsing this thread: 1 Guest(s)