• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
302 headers with manual trans
#1
New to this forum and thank you all in advance for your help. I have a '73 convertible with a 302 and a 3 speed stick. Here is my problem. I've installed aftermarket SpeedPro/ ProComp aluminum heads and I want to keep the z-bar for the clutch. I've looked many places and ordered two sets of shorty headers that don't even come close to fitting. I have to think I'm not the first one to run into this problem. Anyone else had this problem and how did you get it resolved?
  Reply
#2
https://www.summitracing.com/parts/pte-h...refilter=1

these say they work with a standard trans.

And welcome from Iowa.

'73 Grandé H Code. Headman long tube headers, T-5 Transmission, 3.70 Traclok, Lowered 1" all around, Aussie 2v heads w/ 2.19 intake, 1.71 exhaust, screw in studs, full roller cam 608/612 lift 280/281 duration LSA 112, Quick Fuel 750 CFM double pumper, AirGap intake.

'73 F code convertible. Bright red. Needs total restore. (IE HOT MESS)

- Jason
  Reply
#3
(07-10-2018, 02:39 PM)73pony Wrote: https://www.summitracing.com/parts/pte-h...refilter=1

these say they work with a standard trans.

And welcome from Iowa.

I believe that those were the first ones I tried. The aluminum heads have higher exhaust ports and these run smack into the middle of the bar.
  Reply
#4
You might try FPA, they have headers for Yates high port 302 heads.
http://www.fordpowertrain.com/FPAindex/headers2.htm



“If you can't explain it simply, you don't understand it well enough.”
--Albert Einstein
  Reply
#5
(07-10-2018, 03:59 PM)Don C Wrote: You might try FPA, they have headers for Yates high port 302 heads.
http://www.fordpowertrain.com/FPAindex/headers2.htm

just called them, closed until thursday and 5 weeks out on production
  Reply
#6
Running the repop tri-y headers, clears the Z-bar just fine.


  Reply
#7
Hello & Welcome from across the pond in the UK

Steve
1971 Grandé
  Reply
#8
(07-10-2018, 08:52 PM)Hemikiller Wrote: Running the repop tri-y headers, clears the Z-bar just fine.

On a 302 with aftermarket heads?
  Reply
#9
(07-11-2018, 08:23 AM)Daves73 Wrote:
(07-10-2018, 08:52 PM)Hemikiller Wrote: Running the repop tri-y headers, clears the Z-bar just fine.

On a 302 with aftermarket heads?

302 with stock heads. Clears everything by a mile. 

https://summitracing.com/parts/pte-h8426...el/mustang


  Reply
#10
I tried a couple of different headers for my 5.0 with Ford gt40 heads with no luck.  The ports were always to small on the headers.  I kept the JBA 1650SJS headers and installed a hydraulic system.
  Reply
Share Thread:  


Possibly Related Threads...
Thread Author Replies Views Last Post
  FPA headers on a '73 fastback help!! BrandonDindorf 5 945 Yesterday, 11:56 AM
Last Post: Carolina_Mountain_Mustangs
  Hooker competition headers issue Ballaratcastle 15 430 11-05-2018, 10:16 PM
Last Post: Ballaratcastle
  Advice on cheap headers? scgamecock 21 548 10-31-2018, 06:01 PM
Last Post: barnett468
runninpony Hooker headers extra tube bit? Ballaratcastle 2 194 10-24-2018, 12:43 PM
Last Post: Ballaratcastle
  71 vert dual exhaust, longtube header, 302 2V, reinforcement torque plate 1971V8 11 352 09-29-2018, 09:53 AM
Last Post: c9zx
  headers 164runner 11 491 09-25-2018, 01:36 PM
Last Post: Don C
  71, 302 engine gauge feed wiring misterjason 2 298 09-18-2018, 10:28 AM
Last Post: misterjason
  429 motor and c6 trans Newold 3 325 09-09-2018, 06:23 AM
Last Post: Hemikiller



Users browsing this thread: 1 Guest(s)