• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
302 engine identification & specs
#1
I'm having some trouble determining what engine I have and what tune specs.
The engine is stamped E8SE which I believe is 1988 thunderbird engine yes/no?
What are the best spark plugs?  plug gap?  points gap?  timining?
Right now it has Motorcraft AWSF 44c plugs (gapped at approx .050)

thanks
Bob
  Reply
#2
(01-10-2019, 01:50 PM)rjpohl Wrote: I'm having some trouble determining what engine I have and what tune specs.
The engine is stamped E8SE which I believe is 1988 thunderbird engine yes/no?
What are the best spark plugs?  plug gap?  points gap?  timining?
Right now it has Motorcraft AWSF 44c plugs (gapped at approx .050)

thanks
Bob

That is correct the 5.0 block is for an 88 T Bird. What heads do you have, stock, Gt40, etc. The stock 87-88 T Bird heads were not cast just for a Thunderbird, If stock I think they are E6AE head or E7TE. Are you running the stock EFI on it?
  Reply
#3
(01-10-2019, 04:19 PM)rackerm Wrote:
(01-10-2019, 01:50 PM)rjpohl Wrote: I'm having some trouble determining what engine I have and what tune specs.
The engine is stamped E8SE which I believe is 1988 thunderbird engine yes/no?
What are the best spark plugs?  plug gap?  points gap?  timining?
Right now it has Motorcraft AWSF 44c plugs (gapped at approx .050)

thanks
Bob

That is correct the 5.0 block is for an 88 T Bird. What heads do you have, stock, Gt40, etc. The stock 87-88 T Bird heads were not cast just for a Thunderbird, If stock I think they are E6AE head or E7TE. Are you running the stock EFI on it?
I'm not sure what heads I have (I know very little about the history of this car, engine is in a 73 mustang).  Is it easy to identify the heads?  Has older distributor with points/condensor.  It was running but was pumping oil out when running.  I found that the guy had 2 pcv valves (one on each valve cover, passenger side ran to air cleaner, driver side had to front of carb).  I pulled plugs to check and clean, I set gap at .054 and put plugs back in, car wouldn't start.  I also found that the coil had positive post going to distributor, I believe positive should go to starter solenoid.  Right now it will start for just for a second and die. Pretty sure it's getting gas, when I pump pedal gas shoots into carb.

Thanks for the help
Bob
  Reply
#4
Plug gap is determined by the ignition system. A points system is around .030". Using the newer style heads, I'd simply spec out a set of plugs for an '88 5.0 Mustang and adjust the gap to suit the ignition.

Link to '73 wiring diagrams

https://www.7173mustangs.com/images/1973_full.pdf

Also, look on the top of the block behind the intake. There should be a partial VIN stamped into a flat pad. That'll help ID what year the engine is and what it was originally installed in.

[Image: 90616d1266250333-engine-block-numbers-81...ockvin.jpg]


  Reply
#5
(01-10-2019, 06:16 PM)Hemikiller Wrote: Plug gap is determined by the ignition system. A points system is around .030". Using the newer style heads, I'd simply spec out a set of plugs for an '88 5.0 Mustang and adjust the gap to suit the ignition.

Link to '73 wiring diagrams

https://www.7173mustangs.com/images/1973_full.pdf

Also, look on the top of the block behind the intake. There should be a partial VIN stamped into a flat pad. That'll help ID what year the engine is and what it was originally installed in.

[Image: 90616d1266250333-engine-block-numbers-81...ockvin.jpg]
Just making sure I understand, you're saying I should set the plug gap to .030 (because I have points) and that I should use what ever plugs are spec'd for the 88 thunderbird 302 enginge (I am pretty certain it is a 88 engine).  The plugs that are in it (and it was running) look good and they were set at .050.  I re-set them to .054 as recommended for 88 engine. 
From what I can tell points should be set at .016 to .018.  Does this sound right?
Timing set at 10 to 12 BTC???
 
thanks
Bob
  Reply
#6
(01-10-2019, 06:46 PM)rjpohl Wrote: Just making sure I understand, you're saying I should set the plug gap to .030 (because I have points) and that I should use what ever plugs are spec'd for the 88 thunderbird 302 enginge (I am pretty certain it is a 88 engine).  The plugs that are in it (and it was running) look good and they were set at .050.  I re-set them to .054 as recommended for 88 engine. From what I can tell points should be set at .016 to .018.  Does this sound right?Timing set at 10 to 12 BTC???

thanks
Bob

Yes, it may be an '88 engine, but your ignition is vintage '73 (or so). The 88 had the TFI electronic igntion and some sort of fuel injection. 

Ignition tune up specs are in your 73 shop manual.


  Reply
Share Thread:  


Possibly Related Threads...
Thread Author Replies Views Last Post
  Post your burbling bit (Engine) 1sostatic 7 290 5 hours ago
Last Post: 1973machi
  Engine breakin oil question EvilPuppetMaster 10 193 Yesterday, 09:36 PM
Last Post: EvilPuppetMaster
  Headers to fit '72 Mach 1 w/400 engine MeanMachine 7 206 03-22-2019, 04:25 PM
Last Post: donkost
  351C 4V - 72 Mach 1 Engine fan baz70 16 518 02-21-2019, 09:13 AM
Last Post: Stanglover
  71 Mach 1 302 2V carb jowens1126 11 404 02-04-2019, 09:39 AM
Last Post: jowens1126
  Engine/dyno/speed programs mbrew2 3 231 02-03-2019, 09:28 AM
Last Post: c9zx
  73 302 ro 351w swap now transmission noise samckay 17 607 02-02-2019, 04:10 PM
Last Post: tony-muscle
  Thermostat - 302 Parkka 4 190 01-23-2019, 10:41 AM
Last Post: Parkka



Users browsing this thread: 1 Guest(s)