• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
1971 351C 2V Intake and carb question.
#41
(01-10-2019, 09:50 PM)73droptop Wrote: All said and done how many new Pony's you think you will be adding to stock HP?

To be honest I have no idea??  Has to be an improvement from the stock 2 barrel and exhaust manifolds with single exhaust though. Should be a decent seat of your pants improvement and sound way better. Right now its quiet, like a sewing machine. Should be more snappy and sound way better.

Anyone know what a stock 1971 351C 2v is rated at for HP??

Kevin

1971 Mach 1
408C Stroker
C4 w/3,000 stall
8.8" Rear w/3.73's
Disc brakes all way around.

[Image: 28ivsix.png]




                                                                                             
  Reply
#42
I think the 71 351 2v was 240 hp gross, not net.

'73 Grandé H Code. Headman long tube headers, T-5 Transmission, 3.70 Traclok, Lowered 1" all around, Aussie 2v heads w/ 2.19 intake, 1.71 exhaust, screw in studs, full roller cam 608/612 lift 280/281 duration LSA 112, Quick Fuel 750 CFM double pumper, AirGap intake.

'73 F code convertible. Bright red. Needs total restore. (IE HOT MESS)

- Jason
  Reply
#43
I prefer Holley carburetors over Edelbrock carbs. Edlebrocks are nothing more than a copy of the Carter AFB which were primarily factory installed on Chrysler corp. engines. 24 years ago I installed a performer intake and 1406 Edlebrock on my H code. At the time Edelbrocks were cheaper than Holleys and I was on a budget but in the end I spent about the same had I just bought a Holley. It required extensive tuning to get it to operate satisfactory as well as a spacer to be able use the stock air cleaner. I bought the tuning kit with and a few extra metering rods. I had to make a bracket to relocate the throttle cable bracket to align with the throttle lever with the cable (due to the Edelbrock's increased width). After a year it freaked out and needed a rebuild which I did. I later replaced it with a Holley 80457 Holley 600 cfm (4160) and made a couple of jet changes and the improvement in overall performance was vastly improved. I later added a secondary metering block conversion kit (making it a 4150 series) to be able to change the secondary jets for dyno tuning purposes. I was able to ditch the spacer, put the throttle and fuel inlet back to it's original locations as well. I have run this Holley for over 20 years with 1 minor rebuild. I sold the Edelbrock (at a major discount) to a good friend of mine for a 67 Dodge Polara. It fits his 383 like a glove and Eddy is much happier there. In conclusion the Holley's are dimensionally similar to stock Ford carburetors and in my opinion just seem to work and look better on Ford engines.
  Reply
Share Thread:  


Possibly Related Threads...
Thread Author Replies Views Last Post
  D1ZF GA Carb Raven 1 133 01-15-2019, 02:57 AM
Last Post: secluff
  4300D Carb Flooding - replacement? F16Dad 14 825 01-10-2019, 01:44 PM
Last Post: Raven
  Tim meyer 351c thermostat and restrictor plate EvilPuppetMaster 11 425 12-30-2018, 08:27 AM
Last Post: EBSTANG
  Intake valley pan, reuse it??? scgamecock 11 466 12-20-2018, 05:42 PM
Last Post: barnett468
  351C Stumbling at low RPM TheDude 21 584 12-19-2018, 11:53 AM
Last Post: barnett468
  What to do to 351c 4v heads? scgamecock 45 1,687 11-19-2018, 09:27 PM
Last Post: jpaz
  Intake have to be on for a compression check? scgamecock 9 463 11-15-2018, 09:17 PM
Last Post: barnett468
  Edelbrock Torquer intake scgamecock 6 320 11-09-2018, 11:56 AM
Last Post: scgamecock



Users browsing this thread: 1 Guest(s)