• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
rear brake lines
#1
While waiting for my engine rebuild I'm replacing front and rear brakes. The lines were frozen to the wheel cylinders so the lines broke off. I have new wheel cylinders, but the lines have smaller fittings into the rear block on the axle. The cylinder ends are fine. Is it ok to add an adapter to the block end for both lines

[Image: 1_30_09_13_10_12_32.png]
Alan L
  Reply
#2
You can ad an adapter but it can be harder to chase down any leaks, more fittings mean more connections means could have more leaks. You will need to make sure the adapters take flared lines. You can't just use some NPT fitting like for the cooling or fuel system, the brakes are much higher pressure over 600 psi so you have to use special adapters to stop leaks.

You may want to make sure you have the correct wheel cylinders or the correct brake line for your application before dealing with any adapters. Personally I would not use adapters in the brake system.

On a disc brake car there is one brass coupler on the passenger side that connects the hard line to the firewall line, it is designed to take double flairs.

As is the distribution block on the rear axle. The wheel cylinders except the flair from the hardline connection, so if you installed an adapter there it would need to take the flair from the hardline, and have a female inside the other side to go into the male cone in the cylinder.

If you simply install a regular step down adapter there it will blow brake fluid all over the first time to pump the system when the bleeders are closed.
  Reply
#3
(10-03-2010, 02:08 PM)72HCODE Wrote: You can ad an adapter but it can be harder to chase down any leaks, more fittings mean more connections means could have more leaks. You will need to make sure the adapters take flared lines. You can't just use some NPT fitting like for the cooling or fuel system, the brakes are much higher pressure over 600 psi so you have to use special adapters to stop leaks.

You may want to make sure you have the correct wheel cylinders or the correct brake line for your application before dealing with any adapters. Personally I would not use adapters in the brake system.

On a disc brake car there is one brass coupler on the passenger side that connects the hard line to the firewall line, it is designed to take double flairs.

As is the distribution block on the rear axle. The wheel cylinders except the flair from the hardline connection, so if you installed an adapter there it would need to take the flair from the hardline, and have a female inside the other side to go into the male cone in the cylinder.

If you simply install a regular step down adapter there it will blow brake fluid all over the first time to pump the system when the bleeders are closed.

Are rear whl cyls. the same for 1 3/4 and 2" rear brakes? I have 2" rear shoes and the new whl cyls. look the same except the threads for the line is smaller.

[Image: 1_30_09_13_10_12_32.png]
Alan L
  Reply
#4
Something isn't right is your car front disc and rear drum or drum and drum?

I believe the 2" is for front drums I need to look at my book, I could be wrong and 2.25 is front but the wheel cylinders should have the same threads. Where did you get the wheel cylinders?

Thinking out loud, you might have the wheel cylinders for the 250 not the 351
They made different cylinders for the i6 verse v8
  Reply
#5
There are several different size rear wheel cylinders (piston/seal/bore sizing). I learned that while sourcing them for my '72. It is important that from side to side they are the same, and they should be the appropriate size for your application (disk/drum, drum/drum, and possibly engine options). I don't have the breakdown on what the sizes were by application.

[Image: 4zw1hv.png]
Dave

1931 Ford Model A Station Wagon
1969 Mach 1 - 351C, TKO-600, 4WDB, R&P, A/C, Shaker, Fold Down, etc.
1972 Mach 1 - 351C, FMX, PDB, PS, A/C, Fold Down, Console
1996 Mustang Cobra Convertible - 10psi Procharger
  Reply
Share Thread:  


Possibly Related Threads...
Thread Author Replies Views Last Post
  73 Master cylinder/brake booster combo LOUHABY 8 230 07-28-2018, 06:00 AM
Last Post: NOT A T5
runninpony brake pedal travel NOT A T5 4 201 07-24-2018, 05:05 AM
Last Post: NOT A T5
  Underdash brake pedal support turtle5353 17 415 07-19-2018, 05:18 PM
Last Post: c9zx
  rear suspension 71_resurrection 2 185 07-16-2018, 01:56 PM
Last Post: Hemikiller
runninpony Brake Pedal Push Rod NOT A T5 5 271 07-11-2018, 05:47 PM
Last Post: Carolina_Mountain_Mustangs
  Rear brakes sticking sometimes?? turtle5353 12 280 07-11-2018, 01:30 PM
Last Post: turtle5353
runninpony Parking Brake Clip NOT A T5 6 247 07-11-2018, 05:18 AM
Last Post: NOT A T5
  Parking brake cables shaheenk 3 209 07-03-2018, 02:57 AM
Last Post: shaheenk



Users browsing this thread: 1 Guest(s)