• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Q code caband intake
#1
i have a late 71 build Q code and when i got it it came with a Holly 3310 and a aluminum ford intake on the car,and three intakes and another carb in the trunk. what should my stock pieces be? spred bore or square?got a couple of each.any info from u guys will be greatly appreciated
  Reply
#2
Please confirm the following before making a decision. I believe the intake would have been "spread bore" to accept an Autolite 4300D carb. I'm not sure if the intake casting number would have been a D1 or D2 number. That late in the year D2 coded parts could well have been installed (i've found a few D3 coded pieces were used on my 03/72 built Mach 1. Hopefully someone will confirm or correct what I've said.

Good Luck,
Chuck

Edit: I did a little research. i confirmed "spread bore" intake and matching 4300D carb. The over the counter intake mentioned below has a casting number of D1ZX-9424-DA. They are very pricey.
  Reply
#3
Ford did make "service parts" that used a square flange aluminum intake and a 750 Holley Vacuum carb. These were offered as replacement for the Boss 351 and 351 HO. This is the combination we are using on the stock eliminator car. My understanding is these service parts are fairly rare.

Jeff T.

Low buck, touring style, '73 Convertible "rolling restoration", 351c, 2v heads with a shave and a haircut, Performer intake, Holley 650(ish), roller rockers, screw in studs, guideplates, stainless valves, Duraspark / Motorsports MSD, T-5 conversion. 1-1/8" front, 3/4" rear swaybars KYB shocks and some home brewed subframe connectors. Future plans; JGC steering box, Cobra brakes and... paint, interior, etc.

When I die I want to die like grandpa, peacefully in my sleep... not screaming, like his passenger.

[Image: 1_12_09_14_10_15_11.png]
  Reply
#4
thank you guys for the info,when i bought the car the owner told me the drive train had some "special ford pieces"but i chalked that up to salesman ship.it was a fast car when i put it up,almost keep up with my built 89LX
  Reply
#5
If you can find a part number on the intake I can check with my buddy to verify what it is.

Jeff T.

Low buck, touring style, '73 Convertible "rolling restoration", 351c, 2v heads with a shave and a haircut, Performer intake, Holley 650(ish), roller rockers, screw in studs, guideplates, stainless valves, Duraspark / Motorsports MSD, T-5 conversion. 1-1/8" front, 3/4" rear swaybars KYB shocks and some home brewed subframe connectors. Future plans; JGC steering box, Cobra brakes and... paint, interior, etc.

When I die I want to die like grandpa, peacefully in my sleep... not screaming, like his passenger.

[Image: 1_12_09_14_10_15_11.png]
  Reply
#6
C1ZX 9425 DA on the aluminum intake,D1ZE 9425 BB on the spread bore and D0AE 9425 L on the square bore and for some reason a EDELBROCK 2750 2V intake new in the box.any help on the ford # would be great
  Reply
#7
pitbullrescue;17312 Wrote:C1ZX 9425 DA on the aluminum intake,D1ZE 9425 BB on the spread bore and D0AE 9425 L on the square bore and for some reason a EDELBROCK 2750 2V intake new in the box.any help on the ford # would be great


Here you go

http://www.mustangtek.com/FordIntake.html
  Reply
#8
The -DA is a keeper to use or sell/trade. It was an over the counter Ford part and served as the basis for the later "Shelby" intake and the Blue Thunder intake. The -BB is very likely the original intake. The D0AE is from 70 or early (prior to May 71) 71 intake.

Chuck
  Reply
#9
thanks to both of you for the info,i will definitely keep it,seemed like a great combo,just wondering what other parts are in motor now.the amount of info i gained the last few weeks is overwhelming,wish i had found this site earlier!
  Reply
#10
The DA intake is the one we use on the stocker.

Jeff T.

Low buck, touring style, '73 Convertible "rolling restoration", 351c, 2v heads with a shave and a haircut, Performer intake, Holley 650(ish), roller rockers, screw in studs, guideplates, stainless valves, Duraspark / Motorsports MSD, T-5 conversion. 1-1/8" front, 3/4" rear swaybars KYB shocks and some home brewed subframe connectors. Future plans; JGC steering box, Cobra brakes and... paint, interior, etc.

When I die I want to die like grandpa, peacefully in my sleep... not screaming, like his passenger.

[Image: 1_12_09_14_10_15_11.png]
  Reply
Share Thread:  


Possibly Related Threads...
Thread Author Replies Views Last Post
  1973 351 H code vacuum routing Mikes73 6 4,437 08-10-2018, 05:12 PM
Last Post: scottyrocks
  INTAKE MANIFOLD PAPPY HAROLD 1 130 08-07-2018, 04:50 AM
Last Post: TommyK
  1972 Q code new carb rugbyguytx 5 798 07-30-2018, 04:13 PM
Last Post: jpaz
  Considering an Intake change 73pony 5 240 07-18-2018, 07:32 AM
Last Post: 73pony
  1971 351c m-code engine Meyer 8 484 06-23-2018, 06:14 PM
Last Post: keiths71
  351C M-Code engine Timing issue! Meyer 25 860 06-17-2018, 08:41 AM
Last Post: Stanglover
  Sensor on vacuum line Q code John J 1 207 06-10-2018, 03:49 PM
Last Post: Don C
  Underside of Intake manifold Studdley 32 941 05-05-2018, 06:21 PM
Last Post: Stanglover



Users browsing this thread: 1 Guest(s)