• 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Which intake/carb combo
#1
Yes, I know there are 6.23 million combinations available. My set-up is for weekend burnouts with a couple trips to the strip, weekend driver, with decent street manners. I've got a 73 351C 2V with FMX, and I need to get some gears for the rear end. I have the CompCams XE262 with .218 - .224 duration, .513/.520 valve lift, 1400 - 5600RPM. Using a carb calculator I learned about in the WFQ, I believe a 600CFM carb would be the best match. But which one? Ease of installation and ease of operation are most important to me at this point.

Now, dual plane or single plane manifold? I've heard good things about air gap intakes. Anyone have experience with these set-ups on a 2V Cleveland?

All suggestions and comments are welcome!

Doc

Doc

[Image: 6y14ea.jpg]

Project started 8-7-10
Completed: All new suspension, rebuilt 351C H Code bored .030 over with mild cam and intake, new 3.50 TracLok, custom exhaust system
Current "mini-project": interior upgrade Undecided
  Reply
#2
DOc if you are not running ram air I would go with the air gap and a holley 650
  Reply
#3
Doc I believe the Edelbrock performer manifold is the rite choice for a mild street motor along with a Holley street avenger carb. The throttle cable and trans kick down rod attach to the Holley with ease. The performer manifold has all the vacuum ports as the stock manifold. With the Air gap manifold their mite be a clearance issue with stock flat hood. The performer is a dual plane that makes good power from idle to 5500 rpm which is good match for the cam. Mike
  Reply
#4
I have the 351 2v fmx. I went with the performer dual plane and 600 edlebrock. comp cam 494 valve lift, 218 duration,1 5/8 long tube headers.325 trac-loc. This may not be the best setup but what an improvement.I gained a lot of HP. My car was a dog before the rebuild.
Mark

My garage http://www.7173mustangs.com/forum-garage...rxt_uid=40

73 mach 1 351c 4v cc ported, torker2, 750 edelbrock,C6.
73 fastback 351c 2v,performer intake,600 edelbrock,fmx, 325 trac-lok.
  Reply
#5
If you don't do a lot of highway driving, the performer rpm and a 3.50 gear with the 600 cfm carb of your choice. If you want something more friendly on the highway then a regular performer with a 3.00 gear.

73 conv. 460, D0VE large valve heads, Performer RPM manifold, Voodoo 227/233 cam, Holley 950 HP carb, C6 trans, 3.25 trak-loc.
  Reply
#6
Great advice, guys. That helps narrow the choices considerably.

Mark I know what you mean about her being a dog before the rebuild. Mine was more like a walrus. Tongue Big Grin

Doc

Doc

[Image: 6y14ea.jpg]

Project started 8-7-10
Completed: All new suspension, rebuilt 351C H Code bored .030 over with mild cam and intake, new 3.50 TracLok, custom exhaust system
Current "mini-project": interior upgrade Undecided
  Reply
#7
I'm running the Performer 2v and a Holley vac secondary carb similar to the 670 Street Avenger with the stock converter and 2.75 gear ratio. I'm pleased with the combination.

Jeff T.

Low buck, touring style, '73 Convertible "rolling restoration", 351c, 2v heads with a shave and a haircut, Performer intake, Holley 650(ish), roller rockers, screw in studs, guideplates, stainless valves, Duraspark / Motorsports MSD, T-5 conversion. 1-1/8" front, 3/4" rear swaybars KYB shocks and some home brewed subframe connectors. Future plans; JGC steering box, Cobra brakes and... paint, interior, etc.

When I die I want to die like grandpa, peacefully in my sleep... not screaming, like his passenger.

[Image: 1_12_09_14_10_15_11.png]
  Reply
#8
Alright, folks, I've decided on the Edelbrock Performer intake #2750 coupled to a Holley 80457 600cfm carb. I've read several articles that recommend that combination, along with your recommendations here. I'm ordering it first thing Monday morning, so if you have some more input, post it now. Smile

Doc

Doc

[Image: 6y14ea.jpg]

Project started 8-7-10
Completed: All new suspension, rebuilt 351C H Code bored .030 over with mild cam and intake, new 3.50 TracLok, custom exhaust system
Current "mini-project": interior upgrade Undecided
  Reply
#9
I believe those are two GREAT choices for you, Doc and that you will be very happy based on your posted desired goals and what you had when you startedSmile.

Sometimes folks (including me) forget what they intended to "build" when they get into it - - You have apparently stayed "true" to your desired outcome.

I am IMPRESSED!

BT

Do the RIGHT thing.
  Reply
#10
X2....

Jeff T.

Low buck, touring style, '73 Convertible "rolling restoration", 351c, 2v heads with a shave and a haircut, Performer intake, Holley 650(ish), roller rockers, screw in studs, guideplates, stainless valves, Duraspark / Motorsports MSD, T-5 conversion. 1-1/8" front, 3/4" rear swaybars KYB shocks and some home brewed subframe connectors. Future plans; JGC steering box, Cobra brakes and... paint, interior, etc.

When I die I want to die like grandpa, peacefully in my sleep... not screaming, like his passenger.

[Image: 1_12_09_14_10_15_11.png]
  Reply
Share Thread:  


Possibly Related Threads...
Thread Author Replies Views Last Post
  INTAKE MANIFOLD PAPPY HAROLD 1 125 08-07-2018, 04:50 AM
Last Post: TommyK
  1972 Q code new carb rugbyguytx 5 789 07-30-2018, 04:13 PM
Last Post: jpaz
  Considering an Intake change 73pony 5 233 07-18-2018, 07:32 AM
Last Post: 73pony
  Autolite 2100 Carb help Pegleg 3 413 05-22-2018, 05:33 PM
Last Post: Don C
  Underside of Intake manifold Studdley 32 938 05-05-2018, 06:21 PM
Last Post: Stanglover
nuke @#$$#@$@ Edelbrock Carb issue rugbyguytx 2 370 03-25-2018, 09:02 AM
Last Post: Stanglover
  Carb selection. klinton994 6 522 02-15-2018, 12:53 PM
Last Post: Stanglover
  Suggestions for carb/intake combination mild rebuild timachone 15 1,033 01-20-2018, 02:15 PM
Last Post: Canted 393



Users browsing this thread: 1 Guest(s)