Search results

All, Has anyone installed their engine & manual trans in one piece ? I have a 460 and toploader going in and have always done it separately. As always thanks for the help... Thanks, Jay

1973 Air Cleaner Ducts and Flex Connector in good shape. No holes or damages to the plastic ducts. The plastic ducts are dirty and have original dealer "Rusty Jones" rust proofing on them. Looking to get $100.00 or best offer + shipping.

Guys, Anyone have one of these transmissions out of the car for a measurement? I need from mounting face @ bellhousing to end of main shaft where it goes in the pilot bearing. Let me know. Thanks, Jay

All, I am looking for a black left (if they are different side to side) front seat belt clasp assembly with sleeve. It is the one with the square push button. I would take both if you have them. Let me know.... Thanks, Jay

Guys, Unfortunately, since I had a brief act of mindlessness the other night and ran over a Belgium block curb and bashed my oil pan pretty good, I am set to pull motor and replace the pan. I have had a annoying drip from the rear main seal since I put this car together and figure "while its...

Hey guys,  I have a very workable driver side front fender. It was originally off my Mach1 and has mostly original paint and no apparent rust through or substantial repairs. It is on a first come first served as per pay it forward guidelines. I also have both sides original doors with bottom...

Guys, Doing a gear change, rear end housing weld repair and general clean up under the back end. I purchased a used rear sway bar and want to install. Would anyone have a few photos of plates installed by leaf springs, my units are all painted and I cannot figure out which one goes where...

I have a late 80's AOD trans for sale. It was out of a 5.0 mustang and it is complete in as removed condition. The car ran and drove prior to removal. Includes flywheel, converter and kick  down cable. Price is $100.00 picked up in northwest jersey. Let me know..... Thanks, Jay

Guys, Isn’t this KevKen’s car in a Craigslist ad for N.Y. ? 

Guys, Installed my rear windshield last week end hopefully for the last time and found my upper left side trim piece is beyond repair. The previous owner must have had it off a few times trying to stop the leaking with tons of black stuff all over. It is bent and twisted especially where the...

Guys, A great Toys for Tots car gathering in South Amboy, NJ tomorrow. This show usually has an turnout of 200 plus cars for a good cause. Typically the Marines take 2-3 box truck loads of toys and a substantial $$$ from an auction of fun stuff.  So if anyone with or without a car, stop by and...

Guys, Looking for a OEM horn switch. I just picked up a very nice steering wheel and the plastic housing the switch is attached to is broken. Does anyone have one available ?  Let me know.  Thanks, Jay

Guys, Working on getting the front valance, front fenders and bumper fit & assembled correctly. There is a bracket that bolts somewhere between the lower fender edge & valance and go back to radiator support. I did not take this part off of my car, the previous owner did and had both...

Guys, Has anyone used or has knowledge of the "Mustang Market" brand deluxe door panels for our cars ? I have recently installed their headliner and was satisfied with the quality & results.  I haven't heard any news either if the "new" TMI panels are better, worse or just more costly than...

Guys,  Have a new never installed full set of White Deluxe Seat Covers.  They are the comfort weave type. They are very good quality item, ready to be installed on your project. I actually bought these from Don @ Ohio Mustang a few years ago. My little girl, who drives the car more than I wants...

Guys, I am in the process of changing my interior over to white. I need to paint the trim pieces, a pillars and rear seat area plastics. I have read that the plastic panels will paint well if the correct type of paint, proper process and cleaners being used. Any suggestions in brands, etc ...

Guys, Looking for a pair of rear brake backing plates for an 8" rear end. I would prefer a loaded set with all hardware, if possible. Let me know what you have. Thanks, Jay

Guys, As I am in the process of installing a Petronix ignition module in a friends 72 Mach and I have a question. The instructions read to connect red wire to a 12V power source without a ballast or resistor wire. I know from previous experience that our cars have a resistor wire in the harness...

Guys, Working on a hot rod project and looking for a used H-Pipe for 351 4v exhaust (for cheap !!!) I need it for temporary exhaust down pipes with flanges to run this "rat rod" type model A around to shake it out. Pipe could be cut down for easy shipping. Let me know. Thanks, Jay

Guys, After all issues recently with my 351 cleveland, I have found that I need to replace my cam & lifters. I found a Comp cam, thumper series that the profile will suit my needs. I have run Comp cams in the past and have not been satisfied with the lifters due to frequent noise, tapping...